 | | Scout poweroff time out?
|
|
I've just finished a very cool Camera mount that can be controlled via the web. (Linux, NQC & PHP) I've decided to use my scout because it's so limited. I've noticed one point and can't seem to see away way around this. I'm hoping someone can help. (...) (24 years ago, 29-Sep-00, to lugnet.robotics.rcx.nqc, lugnet.robotics.scout)
|
| |
| | Re: NQC & Rotation Sensor
|
|
(...) Do you have the sensor at a place where one rotation of the sensor = 360 degrees of whatever you're turning? I'd suggest putting it somewhere where it rotates a lot more times than the actual turntable. (You need a touch sensor for 0 this way, (...) (24 years ago, 26-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC & Rotation Sensor
|
|
(...) Dave, Thanks for the reply, I had a bad feeling it would be this way. If that wasn't bad enough it keeps losing 2 points when stepped from 0 to 16 and back again... Most annoying. I'm going to move to a touch sensor bump mode... This way my (...) (24 years ago, 26-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: NQC & Rotation Sensor
|
|
(...) The reset is a consequence of one of the bytecodes used to configure the sensor. I don't see a way to work around it. (...) This will have the same problem - in fact the generated code is probably identical (except for perhaps order) to just (...) (24 years ago, 26-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC & Rotation Sensor
|
|
I have this program that monitors the location of a camera mount in a 360 degree turn. (0 and 16 are 0, 8 is 180 etc) However whenever I use SetSensor(SENSOR_2, SENSOR_ROTATION); it blanks the current sensor value when the program is restarted. This (...) (24 years ago, 25-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | WinNQC version 1.01
|
|
When RcxCC's source was opened, I found it wasn't written by C++, so I thought I need to write a new windows tool for NQC, after 3 weeks, I got the first baby. I want to introduce you this new NQC tool - WinNQC, this is a Win32 GUI application, it (...) (24 years ago, 20-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Can't get Linux NQC to compile/Run
|
|
(...) Ok, here is the scoop. I've done the following tests... Installed Red Hat 6.2 Both rpm's worked just fine. (pre compiled & source) Installed Mandrake 7.1 as a 'Developer' (w/ Extension CD) Pre Compiled rpm failed. Same error. Compiled rpm (...) (24 years ago, 15-Sep-00, to lugnet.off-topic.geek, lugnet.robotics.rcx.nqc)
|
| |
| | Re: Can't get Linux NQC to compile/Run
|
|
(...) [ -> followup-top .off-topic.geek ] (24 years ago, 15-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Can't get Linux NQC to compile/Run
|
|
(...) If you can get me an account on a Mandrake box, I'll build an RPM for you and put it on my page. (24 years ago, 15-Sep-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Can't get Linux NQC to compile/Run
|
|
(...) Not after doing an upgrade, but I'd mucked so much around with the system I think I corrupted it. I downloaded and installed Red Hat 6.2 and the pre-compiled version ran. I haven't tried the source compile yet. (I can't get the ftp, telnet & x (...) (24 years ago, 15-Sep-00, to lugnet.robotics.rcx.nqc)
|
