 | | Re: Vision Command on a Mac
|
|
(...) If the mac has pci slots you can install a USB card. this , of course doesnt mean the software will work but you can add USB ports to "some" older macs. I am using a usb/firewire orange micro card in my 7500 power mac ( requires OS 8.6 or (...) (24 years ago, 26-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Vision Command on a Mac
|
|
(...) No chance. The camera is USB. (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Vision Command on a Mac
|
|
I there any way of getting this up and running on an old Mac with serial ports ? For months now I have been trying to figure out a way to accomplish what Vision Command does using third party hardware & software but haven't been very successful. Any (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Problems Solved(WAS Re: Problems with datalog)
|
|
(...) before (...) I just tried using the Wait() command for up to 5 seconds. Still didn't work. I remember reading that the Vision Command required the new firmware. I assumed that VC d/l'd the new firmware automatically. I didn't remember waiting (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems with datalog
|
|
(...) Have you tried putting in a Wait command after creating the Datalog and before you start using it? It must take a few milliseconds to set up. Just my .001 cents after taxes... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems with datalog
|
|
(...) It is possible. If the datalog is created from outside the program (i.e. RCXcc) then my program correctly logs the IR messages. The problem I'm having is that I cannot get the RCX to create the datalog from within the program. From Dave's (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems with datalog
|
|
(...) directly, but that's not possible. A careful examination of the DataLogNext command in the beta SDK documentation shows that the command is quite limited and that you can only log (global) variables, timers, sensor values and the watch/clock. (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems with datalog
|
|
(...) Dave, I'm using NQC 2.2 b1. The firmware filename is firm0328.lgo, the version that came with Vision Command. Ryan -- (URL) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: -raw codes for NQC's Raw command
|
|
(...) I've been sent the format for the codes. Thanks for your help. I've almost completed a new editing/control system for the Mindstorms pbricks. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Problems with datalog
|
|
(...) What version of the firmware are you using (what's the filename of the firmware file)? I think some versions of early 2.0 firmware didn't support creating the datalog from within a program. Also, what version of NQC are you using...I don't (...) (24 years ago, 25-Aug-00, to lugnet.robotics.rcx.nqc)
|
