 | | Re: problems using arrays in NQC
|
|
Hi, you have to tell BricxCC/NQC that you are compiling for the RIS 2.0 firmware. To do this, select "RCX2" in the "Searching for the brick" window that appears at startup (you can also make this the default value in Preferences>Startup). (...) (23 years ago, 27-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | problems using arrays in NQC
|
|
hi I'm building a lego turing machine and in the code certain data values need to be taken into an integer array. (sepcifically, inputing a binary no. using light sensor and a stack of yellow and black bricks). However, the program didn't compile (...) (23 years ago, 27-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Need help with NQC
|
|
I just wrote a program and I can't get it to work. I download it to the RCX and it just runs its motors. I look at the display and push on the bumper and it has those little triagles. So it is not hardware because the RCX reads that the bumper in (...) (23 years ago, 26-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Scout programming
|
|
I used BricXCC and the USB tower to program the Scout. I was wondering how the programming was done by NQC. Are the Scout and RCX command sets compatible? How so? Or does NQC translate and assemble differently depending on target brick? There are (...) (23 years ago, 26-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | NQC 2.4 r3 released
|
|
This is just a bugfix from 2.4 r2. You can download from the usual place... (URL) Baum (23 years ago, 25-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 or 1.5 (minimum requirements)
|
|
Sorry, I don't know if it will run on your system. I only installed it on one machine and hardly use it at all. Dave Baum (...) (23 years ago, 22-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 or 1.5 (minimum requirements)
|
|
I'd suggest not worrying about your system being underpowered. If you've ever programmed before you'll probably want to drop the Lego GUI development environment ASAP and switch to something more powerfull. A first step is to try out NQC which your (...) (23 years ago, 21-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 or 1.5 (minimum requirements)
|
|
Thank you for the answer, but: Do you have any idea whether my system (366 Mhz PII notebook, 64 MB RAM, but only 2.5 MB Video RAM - where LEGO states 4 MB as necessary) could run the original LEGO 2.0 software? Dirk Schlei (...) (23 years ago, 21-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 or 1.5 (minimum requirements)
|
|
The 2.0 firmware is available separately from LEGO as part of the 2.0 SDK. You can use this firmware with a 1.5 set (or even a 1.0 set). If you are not planning on using the Lego software then the only difference between 2.0 and 1.5 is that 2.0 has (...) (23 years ago, 21-Mar-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RIS 2.0 or 1.5 (minimum requirements)
|
|
A more important consideration is whether USB or Serial is more convenient on your notebook. 1.5 comes with a COM port interface, and the 2.0 comes with a USB interface. USB is a lot better, if you have it. (...) (23 years ago, 20-Mar-02, to lugnet.robotics.rcx.nqc)
|
