 | | Re: lnp addressing messages
|
|
(...) Martin Cornelius wrote a nice little piece on this and related isues. it can be found at: (URL) particular look for the sentence: (...) and all shall be revealed :) taken from luis villas legOS howto i initialize lnp on the PC with: (...) (22 years ago, 27-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: lnp addressing messages
|
|
(...) hmmmm..okay.......ill give it a shot. the line below: result = lnp_addressing_write(data,len ,DEST_ADDR,MY_PORT_1); will send a message pointed to by data, consisting of len bytes of data to the DEST_ADDR destination using my MY_PORT_1 port. (...) (22 years ago, 26-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | lnp addressing messages
|
|
I have some problem to understand the lnp addressing message. How to set addresse of computer. How to send a message etc ... I have an example (lnpd example but i don't understand this : #define DEST_ADDR ( DEST_HOST << 4 | DEST_PORT ) result = (...) (22 years ago, 26-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: some problems changing CONF_LNP_HOSTADDR
|
|
hi there, and thnx for the quick reply! so changing the CONF_LNP_HOSTADDR, rebuilding legOS and *.lx program and then download both should work ? oki, ill give it a try tomorrow when i have access to the RCX's. ill also look into the patches you (...) (22 years ago, 26-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: some problems changing CONF_LNP_HOSTADDR
|
|
(...) Hey Ken, I had similar troubles when trying to do development for multiple bots and different LNP addresses. What I found was that I needed to do a fresh recompile of the entire legOS project whenever I changed the LNP ID, as well recompiling (...) (22 years ago, 26-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | some problems changing CONF_LNP_HOSTADDR
|
|
hi all. im currently using legOS 0.2.4.(on linux) i have created a communication algorithm builing on lnp_addressing_write for use with multiple RCX's and as such i need to differ between them. this i thought i could do by changing the (...) (22 years ago, 26-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Camera Shutter Speed Measurement in Legos
|
|
I wrote a little program to measure shutter speeds and it seems to work. It uses a light sensor in passive mode to be more accurate at fast shutter speeds. I think it could be fairly accurate at even 1/1000 sec. If anyone is interested I could send (...) (22 years ago, 26-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Cyggy
|
|
(...) URL. Current Cygwin works very well. The only problem is some Makefile breakage in brickos. BTW, I think hosting that cygwin.exe is a technical violation of the GPL. Max. (22 years ago, 22-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LNP questions
|
|
The variable 'tx_state' referenced in lnp-logical.h will have the value TX_ACTIVE if transmitting. lnp_integrity_write can be blocking for other reasons such as waiting for the xmit buffer to be available or waiting for a delay after transmit (...) (22 years ago, 22-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
| | Cyggy
|
|
I have a vaguely important post which is: the new version of Cygwin is a bugger to get working with Brickos 0.2.6, but the old version, Cygwin B-20 works fine so nobody waste your time on the new version of Cyggy and download it from (URL) for (...) (22 years ago, 22-Aug-02, to lugnet.robotics.rcx.legos)
|
