To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.rcx.legosOpen lugnet.robotics.rcx.legos in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / RCX / legOS / 1144
1143  |  1145
Subject: 
Re: Help with make in Windows
Newsgroups: 
lugnet.robotics.rcx.legos
Date: 
Sun, 11 Jun 2000 20:54:39 GMT
Viewed: 
4654 times
  
Gary-
Unfortunately, I believe that Rossz's tools are known not to work
with NT/w2k. The problem is with the DJGPP toolset itself, not with
Rossz's work. If installing on win95/98 is not an option, you may want to
take a look at

http://erebus.cs.duke.edu/~louie/legos/archives/windows/legOS-0.2.2/

which are instructions that should work for win2k and NT (I think.) Sorry
that that page is so out of date- it's the best advice I can give at the
moment until the new site is organized.

Good luck-
Luis

On Sun, 11 Jun 2000, Gary Mayer wrote:

> Date: Sun, 11 Jun 2000 20:35:31 GMT
> From: Gary Mayer <malekith@charter.net>
> To: lugnet.robotics.rcx.legos@lugnet.com
> Subject: Help with make in Windows
> 
> I have LegOS 0.2.3 installed and, thanks to instructions by Rossz
> Vamos-Wentworth I've gotten quite far down the path of getting the software
> to work.  The firmware works fine and I can upload a demo .lx and have it
> work fine.  However, I can't get make to make a .lx file of my own.  I get
> the following:
> 
>   Makefile:40: .depend: No such file or directory (ENOENT)
>   makedepend *.c -Y -IF:/legOS/include -I. -f- | F:/legOS/util/fixdeps
> F:/legOS/kernel/ > .depend
>   f:/djgpp/tmp/dj210000: makedepend: command not found
>   make.exe: *** No rule to make target `heo.lx'.  Stop.
> 
> I usually wind up with an empty .depend file.  I've looked in the
> f:/djgpp/tmp/ directory and there is no dj210000.
> 
> Now, I'm using Win NT 4.0 and Win 2000.  I've tried it in both and have
> actually gotten further with Win2000 than Win NT 4.0.  I checked and
> rechecked the path settings and they seem OK.
> 
> If I understand the code correctly, it creates a .depend file in the current
> directory and includes this in the compile.  If not, well, I don't seem a
> pre-created .depend file anywhere.
> 
> Any suggestions?
> 
> Thanks in advance,
> 
> Gary Mayer
> 
> 

-----------------------------------------------------------------------

           "Going to California with an aching in my heart.
               Someone told me there's a girl out there
            with love in her eyes and flowers in her hair."
-Led Zeppelin, "Going to California"

-----------------------------------------------------------------------



Message has 1 Reply:
  Re: Help with make in Windows
 
Luis, Thanks for the info. I do have Win 95 and tried installing there ... same errors. Then, I tried the Windows install using cygwin. I've gotten to the end part where you type "make --unix" While it did compile, there were errors along the way. (...) (26 years ago, 12-Jun-00, to lugnet.robotics.rcx.legos)

Message is in Reply To:
  Help with make in Windows
 
I have LegOS 0.2.3 installed and, thanks to instructions by Rossz Vamos-Wentworth I've gotten quite far down the path of getting the software to work. The firmware works fine and I can upload a demo .lx and have it work fine. However, I can't get (...) (26 years ago, 11-Jun-00, to lugnet.robotics.rcx.legos)

14 Messages in This Thread:




Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact

This Message and its Replies on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR