 | | Re: BrickOS motor-output: Subject to change?
|
|
Hi Dietmar, Have you tried brickOS 0.2.6.10? Code was added to that version to address this issue. Mark "Dietmar Cordes" <cordes@lepomux.org> wrote in message news:3F0A7BA7.207050...mux.org... (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
(...) We finally decided to take the time and use Linux to try and get lnpd working. Although we are not familiar with Linux, our professors are helping us. Our main problem now though is the installation of brickOS. I know this should be an obvious (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | BrickOS motor-output: Subject to change?
|
|
Hello, while doing some testing with data transfer wia the motorport of the RCX, I had (again) the problem that the output at full speed (255) is not a constant DC-output. Does anyone have a good solution for this already and will it be part of the (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: robot as input device
|
|
> I assume you want to use the RCX and sensors to collect data and plot/export/do (...) Yes I would like to use sensor data to control objects in a VR-Framework. So it would be possible to use lego RCX data and map it on input device data of the (...) (21 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: robot as input device
|
|
(...) I assume you want to use the RCX and sensors to collect data and plot/export/do calculations using these data. RoboLab Investigator (software) does that. You can have a bot roam around, collect sensor data of all kinds, and upload it to your (...) (21 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: robot as input device
|
|
(...) I don't really understand what you want to do ...... nanobapt (21 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | robot as input device
|
|
Hi, I am not familiar with LegOS but I would like to use the robot as an input device and get all sensor values. Is it possible? regards, kristian (21 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
(...) But remember that changes in the brickOS files and therefore in the resulting brickOS code will allmost certainly crash the user programs. With every new brickOS version you must recompile the user programs that should run on the brick. (...) (21 years ago, 4-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | USB tool under linux
|
|
Hello there .... I'm really interest about driving the lego USB tower but I need some help :) Is someone know how work the USB tower ? How pilot it ? For the camera I've found a better module than the qce-ga one ! The qc-usb is really better (I've (...) (21 years ago, 2-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
(...) Actually, you don't need to do all that. For the last few versions of BrickOS, things are different. The first time you install BrickOS, you: $ cd /brickos-0.2.6.10 $ configure $ make If everything has been installed correctly, you will find a (...) (21 years ago, 2-Jul-03, to lugnet.robotics.rcx.legos)
|
