 | | Re: Motor Control Register (0xf000)
|
|
(...) Thanks for the suggestion... I think the change I made a few days ago included a note here also, but we might be talking about different spots. Let me know if not... kekoa@stanford.edu. -Kekoa (22 years ago, 20-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | LegOS/BrickOS on Mac OS X?
|
|
I was wondering if anyone had successfully ported the H8 compiler over to OS X? With an USB IR Tower, and the underlying Unix/BSD resources on the Mac, it would be an ideal development platform. I've tried compiling the H8 Cross compiler without (...) (22 years ago, 20-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LNP-problem...
|
|
Why don't you post the code you're using. Then we can tell you if it's a problem with the program. Steve ----- Original Message ----- From: Tom Wouters <aqua@no__spam.ulyssis.org> Date: Wed, 20 Nov 2002 17:21:47 GMT To: (...) (22 years ago, 20-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | LNP-problem...
|
|
hi there we seem to have a not so tiny problem with lnp, we can send messages from the tower to the rcx, but until now we have failed to get the rcx to send a message tot the computer, we have tried various versions of the legos kernel, none of them (...) (22 years ago, 20-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS & Cygwin
|
|
(...) You bet. I've fixed this in CVS so it will be in our next test release. Thanks for reporting it. (This is why we do test releases ;-) Regards, Stephen -- Stephen M. Moraco stephen@debian.org (22 years ago, 19-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | BrickOS & Cygwin
|
|
I've downloaded and installed test release 09. Once again things worked very well. But there is one definite problem with this release (as well as 08) when running under Cygwin. In Makefile.Common the lines ifdef BUILDING_HOST_UTILS # ---...--- # (...) (22 years ago, 19-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) As it is, it seems[1] that two of the three NAND gates in the 74HC10 are being used as a driver for speaker output (it's odd that it's two, not one though). So, this leaves one three input NAND gate to do the decoding. Now that I think about (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
<snip> (...) Ok, thank you for the explaination! I am thinking that the Memory Manager would need some rework to support this, since the start of memory is currently established at compile time. I will have to take a look at this (time allowing). (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) I have implemented what Mark Riley has suggested. I submitted a patch to the patches section at the sourceforge project page. The changes are quite small but require some tricky tweaks to the build process. I have only minimally tested it and (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Control Register (0xf000)
|
|
(...) While you are at it you could also make a remark near the explanation of the f000 motor control register, and make it clear that this is a hardware function. When I started to use this extra memory in leJOS I missed the remark at the very end (...) (22 years ago, 14-Nov-02, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
