 | | Re: Motor Speed value interpretation?
|
|
(...) My birth name is actually Ross, but I changed it to Rossz when I married my Hungarian wife. In her language it means 'bad'. :) Rossz (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: C++ OverHead
|
|
(...) Hi, unfortunately I am unable to answer your question, however I am very interested in what you are doing with GA. I recently recieved my RCX and have done GA work in the past as part of my schoolwork. I would love to try using some GAs with (...) (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Parallel sensor problem
|
|
Bernardo Dal Seno <piu1759@cdc8g5.cdc.polimi.it> wrote in message news:87d7dd25ge.fsf@...o.bogus... (...) crane, and (...) RCX 2. (...) like: (...) Thanks. I'll try that. (...) happens (...) connected to (...) Nup. I disconnected the motor, but the (...) (24 years ago, 24-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Parallel sensor problem
|
|
(...) I don't know if this is your problem, but the input ports have polarity (one lead is connected to ground and the other to +5V through a resistor, if I remember correctly). Have you tried to change polarities? (...) Maybe the problem is not in (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: LegOS 0.2.5 and LNP
|
|
(...) On the RCX the LNP handlers are called from an interrupt handler, so after the execution of lnp_*_set_handler() you can safely assume that the old handler will not be called any more. On a PC things are different, there is a problem. I didn't (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: C++ OverHead
|
|
I seem to recall someone doing some testing that showed that C++ programs worked out to take out somewhere around 2 to 3 times the space of comparable C programs. However, I'm sure that varies. Luis (...) ---...--- "Nobody ever said that democracy (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Speed value interpretation?
|
|
(...) As far as I can tell, the speed value really affects power output. This indirectly affects speed, but not in a very happy way. You end up with a wide range of values that give you nearly the same speed, then a very short range that decreases (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | C++ OverHead
|
|
Hi all, a simple question ( I hope) I'm running a small GA on my rcx block , and I'm fairly happy qwith my results so far, it evolves well tot he conditions, however I'd like to try something new <g>... I'm going to try to evolve sub-sumptive (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Parallel sensor problem
|
|
Hi, all. I'm experiencing a strange problem. I'm using two RCXs to control my crane, and I have a single touch sensor connected to input 1 on RCX 1 & input 2 on RCX 2. However, when I run both programs, which both have a wait_event function like: (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Motor Speed value interpretation?
|
|
(...) Greetings! Another Ross!! That's three hangin' around here now!! Well, OK ones a Rossz, but it's close enough! (...) driven (...) have (...) two (...) you (...) hit (...) Well, you could work it out really carefully, but then you've gotta take (...) (24 years ago, 23-Jan-01, to lugnet.robotics.rcx.legos)
|
