Results 981 – 1000 of about 5300.
|
Search took 0.02 CPU seconds.
|
|
| |
|  
rcx
(score: 0.765)
|
|
 | | RE: Anyone made animatronics with the RCX yet?
|
| (...) I know this only works with pbForth, and it's not ALL Technic, but you can drive standard servos with the RCX. Here's how: (URL) You can even drive pneumatic switches with the servos... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH (...) (26 years ago, 21-Jan-01, to lugnet.robotics.rcx)
| |
|
rcx, how
(score: 0.764)
|
|
| | Re: Help with 9738 LEGO Mindstorms Remote Control
|
| (...) Robolab uses the same firmware as Mindstorms RIS, so the remote should work fine. Same goes for NQC. (...) You can write programs in NQC (also in RCX Code or Robolab) that respond to IR Messages. These messages can be sent from another RCX, (...) (27 years ago, 13-Jul-99, to lugnet.robotics.rcx)
| |
|
ris, rcx, ir
(score: 0.764)
|
|
| |
|
rcx, how
(score: 0.764)
|
|
| | Re: Interesting BrickOS Timing Results
|
| (...) I've found that any interrupt on the RCX has a minimum overhead of 101 to 113 states (or about 7 us). This is the time taken by the CPU to recognize and dispatch the interrupt plus the time the ROM routine takes to dispatch the interrupt to (...) (24 years ago, 15-Jan-03, to lugnet.robotics.rcx.legos)
| |
|
rcx, how
(score: 0.764)
|
|
| | Interesting BrickOS Timing Results
|
| Hi All, The recent posts about interfacing an i2c device to an RCX sensor port (in .robotics) got me interested in looking at the kernel code that handles the sensors. So, I did and found myself looking at the ds_handler function. This function is (...) (24 years ago, 14-Jan-03, to lugnet.robotics.rcx.legos)
| |
|
rcx, how
(score: 0.763)
|
|
| | Re: About SetSerialComm(SERIAL_COMM_DEFAULT);
|
| hi Zhengrong, Sorry, I didn't understand (or read) your message well, I thought you were looking for communicating with a PC. Well as far as my knowledge reaches, I agree with Dave, the RCX can't receive raw data (except for program downloading, (...) (25 years ago, 8-Sep-01, to lugnet.robotics.rcx.nqc)
| |
|
rcx, ir
(score: 0.763)
|
|
| | Communication between RCX's with BrickOS
|
| Hello Everyone, I have been working on a dual RCX robot for quite some time now, and have just recently upgraded to BrickOS. At first I attempted to used the LNP communication functions, such as lnp_adressing_write. I am not an expert, and I got (...) (24 years ago, 2-Jan-03, to lugnet.robotics.rcx.legos)
| |
|
rcx, how
(score: 0.761)
|
|
| |
|
ris, rcx
(score: 0.761)
|
|
| |
|
ris
(score: 0.760)
|
|
| |
|
rcx, ir
(score: 0.760)
|
|
| | Ultimate Expansion set Remote Control?
|
| One of the first things I purchased was the Mindstorms remote control. It is not expensive, less than $20 'merican. It can send messages 1, 2 and 3 (three buttons) It can force motors on forward, or reverse overriding a running program (three pairs (...) (27 years ago, 25-Jan-00, to lugnet.robotics.rcx)
| |
|
rcx, ir, how
(score: 0.760)
|
|
| | How advanced can RCX programming be?
|
| I got my RIS a couple of weeks ago, and I have been building simple robots and programmed them using the program on the RIS cd. I´ve heard that you can program the RCX in very advanced ways, multitasking and so on. How advanced can it be? How do you (...) (27 years ago, 10-Jan-00, to lugnet.robotics.rcx, lugnet.robotics)
| |
|
ris, rcx, how
(score: 0.759)
|
|
| | Re: BrickOS Threading...
|
| (...) To tell you the truth, I'm not exactly sure how the BrickOS PWM works, but I do know the standard RCX PWM simply switches the motors between ON and FLOAT, which will not slow the motor down, when it switches from a high power, to a lower (...) (24 years ago, 16-Dec-02, to lugnet.robotics.rcx.legos)
| |
|
rcx, how
(score: 0.756)
|
|
| | Loading firmware
|
| I am a newbie to RIS 1.0 and would like to install pbforth as my firmware and then use it as my command(programming) language. How do I get started. I have downloaded the Active State Tcl ,rcxtel, and nqc to my computer. Where do I go from here ? (...) (24 years ago, 2-Sep-02, to lugnet.robotics.rcx.pbforth)
| |
|
ris, how
(score: 0.756)
|
|
| |
|
ris, rcx
(score: 0.756)
|
|
| | Re: RF Connection To RCX
|
| (...) Yep! I am going to make the RF/IR adapter plug in front of the RCX. And make my RF tower to replace the IR tower. I know the IR carries on 38.5KHz. Does it mean both transmt/receive signals working in the same 38.5KHz? If so, how can I solve (...) (27 years ago, 10-Jan-00, to lugnet.robotics.rcx)
| |
|
rcx, ir, how
(score: 0.755)
|
|
| |
|
ris, rcx, how
(score: 0.755)
|
|
| | WINLNP QUESTIONS
|
| Dear all, I have some troubles setting up WinLNP. I am new to RCX (2 months) and legOS (1 month) and have not much experience with VC6. I want to set up a line of communication between PC and RCX. I downloaded everything from (URL) and I managed to (...) (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
| |
|
rcx, ir
(score: 0.754)
|
|
| | Re: NQC 2.1 b2 in beta test
|
| (...) I remember discussing this briefly, but I don't think we ever came up with a final "spec" for the feature. Here are the issues I forsee: 1) The IR tower times out. NQC should probably do something to keep it alive - and that "something" should (...) (27 years ago, 13-Jan-00, to lugnet.robotics.rcx.nqc)
| |
|
rcx, ir, how
(score: 0.754)
|
More: Next Page >>
|
