 | | Re: BricxCC & downloading NQC programs failing
|
|
(...) See that is what makes Lugnet such a great resource! I finally decided to try out Bricxcc/NQC (after using BrickOS on Linux) and it worked fine when I was just downloading short "Hello World" programs, but I pretty soon ran into this problem (...) (20 years ago, 30-Oct-04, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
|
| |
| | Re: Can't make dllx - anyone else had this problem?
|
|
Ok, thanks for that. I've got it compiling now - I didn't realise liblnp had to be compiled before dllx! (20 years ago, 29-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Can't make dllx - anyone else had this problem?
|
|
(...) The linker is looking for the file liblnp.dll (Not 100% sure of the extension might be .a or .so). The -L arguments specifies a place to look for libraries and is probably where liblnp.dll is expected. Check this directory for the file. I have (...) (20 years ago, 29-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Can't make dllx - anyone else had this problem?
|
|
I am trying to make all the LNP stuff at the moment. Having followed the instructions for installing dllx according to the readme on the legos.sourceforge.net website, I have come to the part where I type: make depend make in the dllx directory. (...) (20 years ago, 29-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: bad motor output because of lego firmware?!
|
|
(...) I suspect part of this delay is inherant to the firmware, and won't be "patchable" In any case, if you want your extender to be something you can market to most users, it should work with the standard firmware, without modification. Just my (...) (20 years ago, 28-Oct-04, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: bad motor output because of bad lego firmware?!
|
|
(...) The firmware (at least version 0328) intentionally prevents you going directly from forward to reverse (or vice versa). I guess the designers felt this would be too rough on the motors. Try inserting a Wait(50) in your first loop. It'll work (...) (20 years ago, 28-Oct-04, to lugnet.robotics.rcx.nqc)
|
| |
| | bad motor output because of bad lego firmware?!
|
|
Hi there, I've spent the last two days trying to write a function in NQC that transfers data to the Lepomux I/O-extender. The data transfer is normally done by connecting the Lepomux to one of the motor ports. Each transition from one motor state to (...) (20 years ago, 28-Oct-04, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Help installing brickOS
|
|
(...) Sure. The configure script tries to find the gcc cross compiler toolchain for the brick's hitachi processor. This chain is needed to compile brickOS to a program that can be run by the RCX. But it seems that you did not install the tool chain. (...) (20 years ago, 28-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help installing brickOS
|
|
(...) I believe that I had the exact same problem a few weeks ago, but I found that using a pre-built package takes a lot of the hassle out of installing BrickOS. The pre-built packages can be found at: (URL) hope this helps, Timothy (20 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
|
| |
| | Help installing brickOS
|
|
I'm trying to install brickOS 0.2.6.10.6 on WIN NT. After unning "configure" it's busy for along time, and terminates with the message -"No Hitachi gcc compiler found. Please install compiler and try again." Any suggestions? Thanks, Jordon (20 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
|
