 | | Re: BricxCC on Win XP how
|
|
(...) If your green light is on all the time I am amazed that you are successful with any communication. Do you need to do the "open the port and wait 5 seconds" procedure to get RIS, javax.comm, and nqc to work? Something BIOS or hardware-related (...) (22 years ago, 21-Feb-03, to lugnet.robotics.rcx)
|
| |
| | Re: constant green light
|
|
(...) By now I have two more clues: 1) Not only does powering down the PC or booting Linux turn the light Off, but so likewise does a Windows Hibernate. 2) Leaving the port open and unused turns the light Off only until I try a Windows Suspend. (...) (22 years ago, 21-Feb-03, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC on Win XP how
|
|
Again intriguing, again I thank you. /// BricxCC Without Firmware /// (...) Yes, does BricxCC COM1 fail for anyone else when firmware is erased? Anyone? /// Versions /// BricxCC Help About tells me I have "3.3.7.2" of "2/12/2003". Bundled with (...) (22 years ago, 21-Feb-03, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC on Win XP how
|
|
(...) You are welcome. I'm still a bit muddled as to your current situation re BricxCC and your RIS with or without the firmware installed. (...) If the port is in use NQC always reports, in my case, the following message: Could not open serial port (...) (22 years ago, 20-Feb-03, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC on Win XP how
|
|
(...) Wow, key tips, great questions, fun links, thanks again for leading me into hours of enlightening experimentation. As a newbie, I'm surprised to think I see nqc reports port in use by exiting immediately without complaint, and BricxCC reports (...) (22 years ago, 20-Feb-03, to lugnet.robotics.rcx)
|
| |
| | New robotics book by Eric Wang
|
|
New book "Engineering with LEGO Bricks and RoboLab" by Eric Wang. See (URL) . Sample at (URL) More info at (URL) . (22 years ago, 19-Feb-03, to lugnet.edu, lugnet.robotics.rcx.robolab, lugnet.robotics.edu)
|
| |
| | Re: BricxCC on Win XP how
|
|
(...) Which COM port is RIS using? Can you describe exactly what BricxCC says/does when you try to get it to find your brick? Does the tower light come on at all? As was suggested already, try choosing the same COM port that RIS uses rather than (...) (22 years ago, 18-Feb-03, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC on Win XP how
|
|
(...) Did you try to fix communication port instead of using automatic configuration ? On my machine (Win2000) where I have both a serial Spybotics cable and a RIS USB tower, I have to specify the port that BricxCC must use. Philo www.philohome.com (22 years ago, 18-Feb-03, to lugnet.robotics.rcx)
|
| |
| | Re: BricxCC on Win XP how
|
|
Pat For what its worth, BricxCC (latest version) works 100% fine with my Win XP setup. I am however using it with a Spybot and the included serial cable. Good luck with it Regards Philip "Pat LaVarre" <ppaatt@aol.com> wrote in message (...) (22 years ago, 18-Feb-03, to lugnet.robotics.rcx)
|
| |
| | BricxCC on Win XP how
|
|
Is there some trick I need to learn to run BricxCC on Win XP? (...) For me BricxCC hardly ever works. I tried un/installing the last three available versions. Always I fail to connect via serial via IR with my brick. Lego RIS talks no worries, (...) (22 years ago, 18-Feb-03, to lugnet.robotics.rcx)
|
