 | | Re: Problems with changing LNP_HOSTADDR
|
|
(...) With the default CONF_LNP_HOSTMASK (0xf0), the host adress is encoded in the higher 4 bits, so you should write #define CONF_LNP_HOSTADDR 0x10 Eric (22 years ago, 5-Jul-02, to lugnet.robotics.rcx.legos)
|
| |
| | Problems with changing LNP_HOSTADDR
|
|
Hi, since a few hours, I'm trying to give an RCX another LNP_HOSTADDR - so I changed the appropriate line in boot/config.h from #define CONF_LNP_HOSTADDR 0x00 //!< LNP host address to #define CONF_LNP_HOSTADDR 0x01 //!< LNP host address and compiled (...) (22 years ago, 5-Jul-02, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Displaying info while debugging
|
|
Hi Ralph, I mentionned a while ago (see msg #508) that I have a problem with SAVE-SYSTEM. Could it be the same problem? Could it related to the USB driver and that, while saving the system, there is no period of inactivity and the buffer gets full (...) (22 years ago, 4-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Linux driver for USB tower
|
|
Hi, (...) Good point. The tar file can be found at (URL) (22 years ago, 2-Jul-02, to lugnet.robotics.rcx.nqc, lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Displaying info while debugging
|
|
Here it is... : wait 15 0 timer_SET BEGIN 0 timer_GET 0= UNTIL ; I go with 0,15 seconds to be on the safe side; 0,10 seconds is too border line. So now, the first example becomes: : TEST 100 0 DO I CR . wait 7 1 0 MOTOR_SET LOOP 7 4 0 MOTOR_SET ; (...) (22 years ago, 3-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | Re: Displaying info while debugging
|
|
Thanks a lot Ralph, And I'm sure you're right. I tried this: 10000 VALUE CTR : test 100 0 DO I CR . CTR 0 DO LOOP LOOP ; For CTR > 11000, the numbers are displayed one at a time. Below 11000, they're displayed in batch. So, it probably means that (...) (22 years ago, 3-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | RE: Displaying info while debugging
|
|
(...) Mario, I did some checking and I think the real issue is with the USB driver from LEGO. The serial tower does not exhibit this behaviour. It has its own problems, which include falling asleep after 2 seconds of inactivity. So, as far as I can (...) (22 years ago, 2-Jul-02, to lugnet.robotics.rcx.pbforth)
|
| |
| | make a mindstorms robot as telerobot!
|
|
Hello, everyone! It's my first time to send a message here! I've a project which requires me to make a mindstorms robot as telerobot. I'd like to use Java as core control programming language! So far, I just know there're several kinds of (...) (22 years ago, 2-Jul-02, to lugnet.robotics.rcx)
|
| |
| | HOWTO Demo.c
|
|
I was able to fix the previous problem regarding the light sensor Thank u Joseph Woolley for your reply. I have another one In the legOS Howto their is a demo code demo.c which has some task switching examples I am having trouble with the following (...) (22 years ago, 2-Jul-02, to lugnet.robotics.rcx.legos)
|
| |
| | HOWTO Demo.c
|
|
I was able to fix the previous problem regarding the light sensor Thank u Joseph Woolley for your reply. I have another one In the legOS Howto their is a demo code demo.c which has some task switching examples I am having trouble with the following (...) (22 years ago, 2-Jul-02, to lugnet.robotics.rcx)
|
