 | | Re: Firnware 2.0 and RCXCC
|
|
Hi Rob, You can get the original version of RCXCC to support the RCX2 firmware. The main change is to add the following line to your autoexec.bat: SET NQC_OPTIONS=-TRCX2 Of course, you also need the new firmware and a version of NQC that supports (...) (23 years ago, 10-Jul-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RCXcc Missing "disconnect commport"
|
|
hi John, thanks for your fast respons, just what I needed (at this moment ;-)) (...) best regards, Stef Mientki (23 years ago, 9-Jul-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Firnware 2.0 and RCXCC
|
|
Hi Everyone, Like the subject says, I am looking for some info on using the new firmware with RCXCC. Up until now, I have found the old version of NQC written by Mark Overmars to be more than enough for what I need. Just recently, though, I built a (...) (23 years ago, 9-Jul-01, to lugnet.robotics.rcx.nqc)
|
| |
| | RIS 2.0 shipping NOW for free in the US (limited offer)
|
|
Hi, These guys are shipping RIS 2.0 for $189.99. (URL) that you saw it in comp.robotics.misc and give them the following code #1070801crm and get it shipped free to anywhere in the USA. Cheers, Ram -- ,,,, /'^'\ ( o o ) -oOOO--(_)--OOOo---...--- | (...) (23 years ago, 9-Jul-01, to lugnet.robotics.rcx, lugnet.robotics)
|
| |
| | Re: RCXcc Missing "disconnect commport"
|
|
(...) I just uploaded a new zip containing version 3.2.9.7 of RcxCC which now has a menu option available to disconnect the COM port. I'm considering adding COM Automation support to RcxCC so that much of its functionality can be scripted. If anyone (...) (23 years ago, 9-Jul-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RCXcc Missing "disconnect commport"
|
|
(...) Sorry about that, Stef. I'll put that menu option back in today. Thanks, John Hansen (23 years ago, 9-Jul-01, to lugnet.robotics.rcx.nqc)
|
| |
| | RCXcc Missing "disconnect commport"
|
|
hi John (Hansen or Binder ?) I used your RCXcc a few times, but I'm missing a very essential command (which was available in the orginal Mark Overmars RCXcc) "disconnect the commport". I can work around it, but this command could make things easier. (...) (23 years ago, 8-Jul-01, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: RCX Controlled Mobile De-coupler
|
|
I've just completed your version of the decoupler device and I must say that it's excellent! 8-wide train builders may want to modify this for clearance reasons though.-Harvey (23 years ago, 5-Jul-01, to lugnet.robotics.rcx, lugnet.robotics.scout)
|
| |
| | Re: Matlab and RCX
|
|
(...) I have done alot of MATLAB control stuff on SUN's. To control an RCX you will probably have to write a "Mex" interface in C. There is an inerface library for Visual Basic called sprit (??). If this can be accesed as a library from C then just (...) (23 years ago, 5-Jul-01, to lugnet.robotics.rcx)
|
| |
| | Re: constants for NQC using firmware 0328
|
|
(...) The wierd thing about the bytecodes provided by lego for direct serial communication (used by SendSerial() etc.) is that they are Tx only - there aren't any corresponding Rx capabilities. However, its possible that the 4800 baud setting is (...) (23 years ago, 4-Jul-01, to lugnet.robotics.rcx)
|
