 | | Re: Automated Level Crossing using NXT
|
|
(...) break at some point, but you seem to have a pretty good system there. (...) Actually, I think you could do this at least partially with a single sensor. If the train is running at a fixed speed, you can have the program figure that speed out (...) (16 years ago, 5-Sep-08, to lugnet.trains, lugnet.robotics.nxt)
|
| |
| | The LEGO Didn't Break (or the HALE Mission - LEGO where it was never intended to go)
|
|
OK, I'm a little bit proud of this... and, mostly, amazed that it functioned at all. I was selected to participate in the HALE (High Altitude LEGO Extravaganza) after submitted two proposals in the hopes one would make it... and instead, both were (...) (16 years ago, 30-Jul-08, to lugnet.robotics, lugnet.robotics.nxt, lugnet.technic) !
|
| |
| | Re: NXT-G Models in Vista
|
|
(...) Our tech had to take out the Adobe CS3 suite. Now the models show up. But CMU's Robotics Engineering does not. He reports that the old 'NXT clicking" version 1.0 was compatible with Adobe CS3. Seems Lego Tech Support has heard of something (...) (16 years ago, 26-Jul-08, to lugnet.robotics.nxt)
|
| |
| | NXT-G Models in Vista
|
|
I'm teaching this week using laptops running on Vista. The laptops also have the full suite of Adobe software. Under these conditions, the models do not show up. The models momentarily blink onto the screen, then the display goes blank. I suspect (...) (16 years ago, 24-Jul-08, to lugnet.robotics.nxt)
|
| |
| | Re: ONLINE LEGO NXT INTERFACING WORKSHOP
|
|
(...) Do you have any more information on this? It sounds interesting - and I love the HT Prototype board, I'm using it in my HALE mission to run far more sensors and even a heater circuit than I could have otherwise (& I'm lousy at electronics - (...) (16 years ago, 15-Jul-08, to lugnet.robotics.nxt)
|
| |
| | ONLINE LEGO NXT INTERFACING WORKSHOP
|
|
Hi All, I'm in the planning stages for having the first Online LEGO NXT Interfacing Workshop. The hands-on event will be conducted using Skype as participants will be learning the basics of electronics interfacing aided by Hi Technic's Prototype (...) (16 years ago, 15-Jul-08, to lugnet.robotics.nxt)
|
| |
| | Re: NXT-G print to text?
|
|
(...) You can print the program as an HTML file (with images; the environment will auto-generate them), and the environment will even oblige you by printing the hidden tabs of multi-case Switch structures. But there's no "text version" of an NXT-G (...) (16 years ago, 11-Jul-08, to lugnet.robotics.nxt)
|
| |
| | NXT-G print to text?
|
|
In Robolab, one could print to file and read the program methods in text. Is there an equivalent in NXT-G? One of my students has this enormous NXT-G program that is hanging up every workstation we try to debug it in. It has about a dozen loops and (...) (16 years ago, 10-Jul-08, to lugnet.robotics.nxt)
|
| |
| | Re: Bluetooth quirks
|
|
(...) To answer the question, we're using NXT-G. But that was last week's summer camp. This week seems to take 3 pairs of Bluetooth battlebots just fine. (16 years ago, 10-Jul-08, to lugnet.robotics.nxt)
|
| |
| | RE: Bluetooth quirks
|
|
Are you using RobotC or NXT-G? -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On Behalf Of gypsy_fly Sent: Wednesday, July 02, 2008 7:38 PM To: lugnet.robotics.nxt@lugnet.com Subject: Bluetooth quirks I've (...) (16 years ago, 6-Jul-08, to lugnet.robotics.nxt)
|
