 | | Re: How to implement continuous drive with NXT motors?
|
|
"David Wallace" <dww.robotics@gmail.com> skrev i en meddelelse news:JB74z0.K8v@lugnet.com... (...) Same here, except my move will be to Java which I know best. I may try out NBC at some point. It seems to me the downramp in speed when using the (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Bluetooth/Brick
|
|
Dear all, I'm working now with a bluetooth to communicate with my NXT. The comport is COM7. When I run NXT Remote the NXT is responded to the commands. When I run BricxCC the Bluetoot is not recognite, message no connection to the programmable (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: NBC Control of RCX Sensors
|
|
(...) The RCX sensor itself does not work without activating its LED. IN_TYPE_REFLECTION is the mode you should use with it (IN_TYPE_LIGHT_INACTIVE and IN_TYPE_LIGHT_ACTIVE are for NXT light sensor). As you noticed, the RCX light sensor has some (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: NBC Control of RCX Sensors
|
|
Another observation. It seems that the IN_TYPE_LIGHT_INACTIVE is really not meant to be used with the RCX light sensor. There is very little sensitivity with this setting. The IN_TYPE_REFLECTION setting is much more sensitive. Too bad that we lost (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: NBC Control of RCX Sensors
|
|
OK, I answered my own question. I just needed to set the sensor type to: IN_TYPE_LIGHT_INACTIVE for RCX light sensor with the LED ON IN_TYPE_REFLECTION for RCX light sensor with the LED OFF (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | NBC Control of RCX Sensors
|
|
Has anyone tried to control the RCX sensors with NBC? I have the converter cable and hooked up my RCX light sensor, but only got back readings of 53 (percent full scale). I used the NBC SetSensorLight command which should set the sensor to turn on (...) (18 years ago, 2-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: How to implement continuous drive with NXT motors?
|
|
I am not a NXT-G expert. I'm a programmer, so I moved to NBC pretty quickly. It's much easier for me to do things in a language than with graphics (not to mention the programs are 1/10 the size of NXT-G). Good Luck! David (18 years ago, 1-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: How to implement continuous drive with NXT motors?
|
|
"David Wallace" <dww.robotics@gmail.com> skrev i en meddelelse news:JB3HDF.3EL@lugnet.com... (...) I suppose you have to make the change between drive direction blocks by means of some "until sensor actuated" block, then? This was my very first (...) (18 years ago, 1-Jan-07, to lugnet.robotics.nxt)
|
| |
| | Re: Connect BT devices to the NXT without a passkey?
|
|
In article <JAynn0.90L@lugnet.com>, Jordan Bradford <jordan_bradfordREMO VE_THIS_SPAM_THINGY@...tmail.com> writes (...) I have not tried this, but I would expect it to work. (...) Alas, this will not work. Bluetooth is just a means of carrying (...) (18 years ago, 31-Dec-06, to lugnet.robotics.nxt)
|
| |
| | Re: Sending program by bluetooth
|
|
Hi Jan, I had asked this question of John Hansen a while back. His response follows. Note that this reduced my connection time in BricxCC from 17 seconds to 3 seconds. "First use NeXTTool.exe to create a nxt.dat file like so: nexttool -listbricks > (...) (18 years ago, 30-Dec-06, to lugnet.robotics.nxt)
|
