 | | motor command question
|
|
Why would two motors, set to turn and with unlimited chosen for time out, only turn a couple of times and stop. this motor command is the only command in the program. patty (17 years ago, 3-Dec-07, to lugnet.robotics.nxt)
|
| |
| | Re: Nxc and Mindsensors stuff
|
|
(...) Thank you! But it worked only after firmware upgrade (to version 1.05) and using original NXT flat cables (Mindsensors flat cables are very poor quality). -- alf (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
My NXT Charger came with my battery. The output of the charger is 10.8 volts, 700 ma 8W. I would just buy the Lego charger. After reaching a full charge, the charger goes into a trickle charge mode. "Pavel Petrovic" <pavel.petrovic@gmail.com> wrote (...) (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
(...) Whew! I was going to put my question in past tense ("Does this mean that I should have or shouldn't have used the train controller plug ...") but it seemed better to be a fool after doing something not dumb than after doing something dumb! (...) (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
(...) You should. The NXT battery expects the same wallwart as the train controller and RCX. Philo (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
(...) Brian, So, does this mean that I should or I shouldn't use the train controller plug thingy that I use for the trains and my RCX? Rafe (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: recharging NXT battery block with DC adapter?
|
|
(...) I'd say a bad idea, since it's supposed to be supplied with 9-12V *AC* (not DC) power. Like the RCX 1.0, it might work under a DC supply... but that's not what it was designed for. (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | recharging NXT battery block with DC adapter?
|
|
Hi, Can anybody confirm whether recharging a NXT battery block using 9V or 12V DC adapter is a bad or good idea, please? Seems that LEGO published HW schematics for the brick, but not for the battery block... Pavel. (17 years ago, 30-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: Nxc and Mindsensors stuff
|
|
(...) Well, I use Linux so I completely skipped the part about NXT-G in the docs and I missed the reference to the light sensor. Anyway, that is sort of what I tried (I changed the original program so many times I am not sure). But probably I missed (...) (17 years ago, 27-Nov-07, to lugnet.robotics.nxt)
|
| |
| | Re: Nxc and Mindsensors stuff
|
|
(...) I do not have the mindsensors DROD-Nx sensor but I have read the documentation from their website. It says that the sensor is an analog sensor which you can read using the standard NXT-G light sensor block. That means you need to configure the (...) (17 years ago, 27-Nov-07, to lugnet.robotics.nxt)
|
