Subject:
|
Re: Bootstrap Mode, Problem
|
Newsgroups:
|
lugnet.robotics.handyboard
|
Date:
|
Thu, 24 Oct 1996 19:37:26 GMT
|
Original-From:
|
John R. Pope <POPEJ@NAGstopspammers.CS.COLORADO.EDU>
|
Viewed:
|
1661 times
|
| |
| |
Fred,
Thank you very much for your response, I was able to complete the first
step succesfully(1).
However Step 2 does not complete succesfully the Red Led goes off and the
green led stays on.
Here is how my cables are configured when I hooked up my board to the
computer, it is hooked into the
25 pin adapter(in computer), that has 25 to 9 pin then I hooked into a 9 to
25 to hook back to the mini board. So my cables go 25F to 9M connected
to 9F to 25M connected to the miniboard.
Thanks again
John Pope
John.Pope@colorado.edu
popej@ucsub.colorado.edu
popej@nag.cs.colorado.edu
303-786-4272
On Thu, 24 Oct 1996, Fred G. Martin wrote:
> 1. first, check if the board can go into DL mode when it is not attached
> to the host computer. power on with STOP held down, and it should go
> into DL mode, indicated by both the BATT and PWR LEDs lighting briefly
> and then turning off and staying off.
>
> 2. Next hook the board up through interface to the PC and try again
> (before running any SW on the PC). You should again be able to put
> the board in DL mode.
>
> 3. Finally, run IC and go to the boot download mode. when it prompts
> you, connect the HB and put it in DL mode.
>
>
> Please reply with info as to whether this process fails before step 1,
> 2, or 3. YOu only have to hold the Stop buttn until the BATT led goes
> off.
>
> -Fred
>
> In your message you said:
> > I have a handyboard that has been working fine, I pulled it out of a box,
> > where it had sfaely been stored for a month and ran into a problem.
> >
> > I am connecting it to a PC, and using IC v3.1 Beta 3, The Pcode is
> > already on the board. I can get the IC to recognize the board and the
> > fact that it is attached to a com port, 2. However I cannot get the
> > computer to synchronize with the board. I figured I should replace the
> > pcode, but I can't even get the board into the download mode. I press the
> > stop button and hold it down while I turn on the board, then the batt led
> > turns off put the green pwr led still stays lit even after I have held the
> > stop button down for a minute or longer, the lcd goes faint with the
> > blocks across the top shaded in.
> > So does anyone have any suggestions of solutions to my problem, or things
> > I can try in order to get it to work.
> >
> > John Pope
> > John.Pope@colorado.edu
> > University of Colorado at Boulder
> > Computer Science Student.
> >
> >
> >
>
|
|
Message has 1 Reply: | | Re: Bootstrap Mode, Problem
|
| In your message you said: (...) (1) I assume when you say "miniboard," you actually mean the Serial Interface/Charger board. please be careful with your language because the Mini Board is a different specific project that is not part of the Handy (...) (28 years ago, 24-Oct-96, to lugnet.robotics.handyboard)
|
Message is in Reply To:
| | Re: Bootstrap Mode, Problem
|
| 1. first, check if the board can go into DL mode when it is not attached to the host computer. power on with STOP held down, and it should go into DL mode, indicated by both the BATT and PWR LEDs lighting briefly and then turning off and staying (...) (28 years ago, 24-Oct-96, to lugnet.robotics.handyboard)
|
5 Messages in This Thread:
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|