| | re: MCI commands in Visual C++
|
|
hi everyone, ok this is off the topic but i'm hoping someone can help. i can play .wav files using the Multimedia control interface in Visual c++, the only problem is i can't figure out a way to play without having to rewind the .wav file every (...) (24 years ago, 11-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: More on Miniboard woes and woohoos.
|
|
The current version of ICC11 has a builtin downloader that talks to MB. Only for W95/NT/... though. ICC11 works with just about ANY HC11 boards, minus lack of support for paging. (...) -- // richard (URL) (24 years ago, 7-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: Linux and handyboard help!
|
|
I got it!! Thanks! I was loading the wrong library. I had the correct library in the directory, but I hadn't run ic -config and changed it. Thanks again. ___...___ Jesse Dosher, K7DSP University of Washington, Dept. of Electrical Engineering, (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: Linux and handyboard help!
|
|
Chuck, here's the results from ic -config: jdosher@keynes:~...ic/ic:8# ./ic -config Interactive C for 6811. Version 2.860 BETA (Oct 4 2000) IC written by Randy Sargent and Anne Wright. Copyright 1994. (uses board pcode by R. Sargent, F. Martin, and (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: More on Miniboard woes and woohoos.
|
|
(...) I'm hitting two posts at once here... James, It came as a printf.c file with the freeware ICC11 compiler on the Miniboard site. I was curious as it was to be used with the dhry.c code Richard Mann included. However, that dhry.c code when I (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: More on Miniboard woes and woohoos.
|
|
(...) I didn't think printf() was even available on the shareware (old) version of icc? (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: Linux and handyboard help!
|
|
Do an ic -config and check to see what library it downloads, make sure its the handyboard library and the 6.270 board library. --Chuck (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Re: More on Miniboard woes and woohoos.
|
|
If you upgrade to the commercial version of icc11 not only do you get a downloader that works under windows 9x but also very nice library interface. (disclaimer: I wrote the library :-) In general on embedded systems you _don't_ want to use printf, (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | Linux and handyboard help!
|
|
Hi all, HELP! I seem to be having some strange behavior using IC under linux. For some unexplainable reason, when using IC under linux to load a file onto the handyboard, the board's digital inputs don't respond. I can take the same board and the (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
|
| | More on Miniboard woes and woohoos.
|
|
Hi again, Thanks to those who sent suggestions. Running in DOS mode, not W95 dlm does work just fine. Ick. Oh well. Anyway, I thought that 2K of EEPROM would be enough to do something with, and it may be, but probably not in ICC - The printf.c (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|