 | | Re: More on Miniboard woes and woohoos.
|
|
(...) I didn't think printf() was even available on the shareware (old) version of icc? (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Linux and handyboard help!
|
|
Do an ic -config and check to see what library it downloads, make sure its the handyboard library and the 6.270 board library. --Chuck (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: More on Miniboard woes and woohoos.
|
|
If you upgrade to the commercial version of icc11 not only do you get a downloader that works under windows 9x but also very nice library interface. (disclaimer: I wrote the library :-) In general on embedded systems you _don't_ want to use printf, (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Linux and handyboard help!
|
|
Hi all, HELP! I seem to be having some strange behavior using IC under linux. For some unexplainable reason, when using IC under linux to load a file onto the handyboard, the board's digital inputs don't respond. I can take the same board and the (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | More on Miniboard woes and woohoos.
|
|
Hi again, Thanks to those who sent suggestions. Running in DOS mode, not W95 dlm does work just fine. Ick. Oh well. Anyway, I thought that 2K of EEPROM would be enough to do something with, and it may be, but probably not in ICC - The printf.c (...) (24 years ago, 6-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Miniboard download random failures
|
|
(...) "expected (...) James, Yes, I am running from a DOS window in W9X. Do I have to boot to DOS mode to correct for this? Uhm, I'm a Mac person, so, have patience, how does one boot to DOS instead of Win95? thanks, DLC (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Miniboard download random failures
|
|
(...) Are you running DLM from a dos window in Win9x? I've had this problem but it usually stops when I run it in DOS. Just a thought. -Jim Munro <jimmn@xnet.com> (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Freeware ICC11 and bad iasm11.exe?
|
|
Me again, I just got the ICC11 freeware from the Miniboard site and installed it, moving the crt.s over as it says to do in the docs, etc. I tried to compile the test compile of icc11 dhry.c printf.c and got a LOT of "phasing" errors, whatever that (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | Miniboard download random failures
|
|
Hello, I just finished building a Miniboard using the HC811E2 processor. After swapping the Rx and Tx lines on my serial cable the download and reset switch do as the manual says. However, when I use dlm to download a program the bootstrap section (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
| | serial communication
|
|
Hi.. I am also facing problem in serial communications. My problem is that I am trying to use the handyboard to drive a modem. I have used a cross-serial cable to connect my handyboard's external serial board to a modem. But whenever I run my app, (...) (24 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
