|
|
 | | handy board troubles...
|
| Hi, A while ago I shorted out my handy board which caused the ram chip to fry. I've since replaced it, and the board boots again, but I am now seeing other strange behaviour. The batteries are connected and the board recieves power, but when I turn (...) (25 years ago, 20-Mar-00, to lugnet.robotics.handyboard)
| | | | | Expansion board problems
|
| Hi Finaaly got my exp board working and now yet another problem. When checking sensors, every 4 secs or so I always get 255.(when printing sensor value to screen would be like : 2,2,2,2,2,2,2,255,2,...,255,etc., i knew its not the sensor because (...) (25 years ago, 18-Mar-00, to lugnet.robotics.handyboard)
| | | | | Sonar
|
| Hi I use a Polaroid sonar ranging modul with the HB and the expansionboard. It all went well, but by mistake i put the digital in from J12 to a digital out. Since then i get the result -1 and the sonar isn't clicking. I've tried with another sonar (...) (25 years ago, 18-Mar-00, to lugnet.robotics.handyboard)
| | | | | Reset of handy board
|
| hi, may i ask how much current passing through HB will cause the HB reset ?? i have a big problem on my HB, I power one Polaorid 6500 sonar, 1 servo and 2 hacked servos by seperated 6V 1300mAh NiMH battery with common ground, and power 2 GP2D02 by (...) (25 years ago, 18-Mar-00, to lugnet.robotics.handyboard)
| | | | | IR emitters !
|
| Hi ! Can we connect two ir emitters to the HB IRout port (female connector J7) for left and right obstacle detection ? If so ! how do we distinguish between the left IR led and right IR led transmission since I'm planning to use only one Ir detector (...) (25 years ago, 18-Mar-00, to lugnet.robotics.handyboard)
| | | | | Re: sonar
|
| (...) I don't think it matters much. I used a 'lytic and it works fine. If you have another kind, it probably wouldn't hurt to give it a try. -- Will +---...---+ | ^^ <^ ^> | | / òó ó°° \ | | / =Y= U \ | | Wendy, Will, Tatoosh & Tenzing | (...) (25 years ago, 17-Mar-00, to lugnet.robotics.handyboard)
| | | | | Re: sonar
|
| Just wondering... in reference to the modification on the Polaroid 6500 sonar ranging board, there's been two different assertions. Should the 0.1uF cap be of a polarized (e.g. electrolytic, tant, etc.) or non-polarized variety (as stated below)?... (...) (25 years ago, 17-Mar-00, to lugnet.robotics.handyboard)
| | | | | Re: windows nt and handyboard
|
| Thanks for all of you that sent me e-mail regards your experience with hb and windows nt. They are a pretty useful information and i am considering them. lourdes (25 years ago, 17-Mar-00, to lugnet.robotics.handyboard)
| | | | | programming for step motor questions...
|
| Hi, I would like to use step motors in my robot and have had success using the MC3479 stepper motor IC, it is simple to use, just needs a direction bit and a pulse, but I really don't know how to program my hb to do this. I mean I can figure out how (...) (25 years ago, 17-Mar-00, to lugnet.robotics.handyboard)
| | | | | Getting the L297 into wave drive mode
|
| Hi I'm using the L297/L298 chip configuration to run 4-phase unipolar stepper motors. Currently I'm driving them in half-step mode but I'm not getting enough torque.. :( Has anyone successfully gotten the L297 chip into wave drive mode? I believe I (...) (25 years ago, 17-Mar-00, to lugnet.robotics.handyboard)
|
|
