 | | P.W.M into something usefull....?
|
|
Hi all you to all you guys in the HB world!, Found a old RC system for a air plane. Works fine with the 1 servo it had left, my question is how would one go about useing it with the HB? hooked one of the outputs to a analog port and got the P.W.M. (...) (25 years ago, 4-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | new lock_process() function library for IC
|
|
I have written some library code which allows user programs to effectively hog_processor() for a user-specified time interval, instead of the 256 msec allowed by hog_processor(). The new functions are: void lock_process(float seconds) ;locks out (...) (25 years ago, 3-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: servo motors
|
|
Hi, Try adding some delay time between turning the servo on and off. For example, 'sleep(2.0);'. Add the sleep(2.0) as follows: (...) sleep(2.0); /* wait for 2 seconds for servo to move */ (...) sleep(2.0); /* wait */ (...) Probably the reason why (...) (25 years ago, 2-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Converting voltage to resistance
|
|
Voltage and resistance have no relation to each other - they are two different things. The HB analog inputs convert the voltage level applied to them to a digital equivalent, basically an A/D converter. So, you can apply your 0 - 5 volt signal (...) (25 years ago, 2-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | RE: servo motors
|
|
(...) Yes you are right, i just figured out too. i have to give at least 0.3secs for the servo to move to the required position. (...) actually the servo doesn't move when you turn it off. if you don't turn it off some small movements are observed. (...) (25 years ago, 2-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: servo motors
|
|
(...) What is it supposed to be doing? When you say _it_ doesn't work, what exactly is not working? I'm not that familiar with the routines but it looks like you're shutting off the servos before they can move. I also believe once you turn off the (...) (25 years ago, 2-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Converting voltage to resistance
|
|
This is a dumb electrical question. I am a programmer, and I still struggle with the electrical aspects of this hobby. How do I convert voltage output to resistance. I have an application that turns out 0 to +5 volts. However, as I read the (...) (25 years ago, 2-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | servo motors
|
|
hi all i connected a servo to the digital 9 port, downloaded the servo.icb and servo.c files. from the command line i can control the servo. but then i wrote the following very simple code, and it doesnt work. can anyone spot the problem. void (...) (25 years ago, 2-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Exp. board Servo
|
|
(...) Fortunately there is a direct relationship between servo-value and angle. Try different angles (for example 0 / 45 / 90 / 135 / 180 degree) and draw the diagram value vs. angle (for example with MS Excel). You will (hopefully) see a linear (...) (25 years ago, 1-Mar-00, to lugnet.robotics.handyboard)
|
| |
| | RE: HB's mA consume?
|
|
Well, you can _greatly_ increase the efficency of the handyboard if you remove the 7805 regulator and replace it with a PowerTrends switching regulator (Digikey sells these among others). I would suggest you run three wires from the regulator to the (...) (25 years ago, 1-Mar-00, to lugnet.robotics.handyboard)
|
