| | Re: Problem with my board
|
|
In lugnet.robotics.handyboard, Gary Livick <glivick@pacbell.net> writes: The motor doesn't work in my program, which has multiple processes running, but it still doesn't work when i just send the command through IC's interactive window: motor(1,50). (...) (25 years ago, 9-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Re: Problem with my board
|
|
Bob, What other code are you running? What does your motor code look like? Does anything get hot when this happens, like the motor control chip, the hex inverter or the voltage regulator? Gary Livick (...) (25 years ago, 9-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Problem with my board
|
|
I am using a HD with expansion board. Periodically when I run the motors at anything less than 100 they spin with very little power and both the red and green lights on the board light up. At full power the motors work perfectly with only the green (...) (25 years ago, 9-Jan-00, to lugnet.robotics.handyboard)
|
|
| | LEGO IR Remote Control
|
|
Hello All, Has anyone developed an IR receiver/decoder to allow a HandyBoard robot to be controlled by a LEGO IR Remote (#9738)? My LEGO 'bots are great when they're controlled with the LEGO IR remote ... grade school kids really like the remote (...) (25 years ago, 8-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Mic for CCD Camera
|
|
Hi, This question is not HB specific, sorry about that. I have bought a CCD camera board, and I want to add it to my robot together with a TV transmitter, the problem is that the camera has not built in audio, so I will like to know if someone has a (...) (25 years ago, 8-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Re: Voice Recognition
|
|
Hi Sonny, I've played with Voice Direct and also with the HM2007 chip. Both of them work fine in a quiet environment, but in my limited playing they were both overwhelmed by the ambient noise of a moving robot. They both are speaker dependent, and (...) (25 years ago, 8-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Voice Recognition
|
|
Hello all, I have a project upcoming that would benefit from speech recognition. I have seen the voice direct by Interactive Speech and was thinking of integrating it into my robot. If anyone has had any success (or failure) with this product or any (...) (25 years ago, 8-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Re: I NEED HELP
|
|
(...) BG Micro sells an equivalent Toshiba sourced part which I have been using in Rug Warrior without trouble thus far. The price is very good at 6.95 USD in quantity 25. You can contact them at www.bgmicro.com. John Vaughn Hobart & William Smith (...) (25 years ago, 7-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Re: I NEED HELP
|
|
If you need just one 68HC11, give me your address and I'll post it to you. I have some spare ones (second hand). Peter Gasparik (...) robot, but i can´t get the MC68HC11 processor because here (in colombia) is not avaible anywhere (...) avaible, is (...) (25 years ago, 7-Jan-00, to lugnet.robotics.handyboard)
|
|
| | Re: Servos, power, and the expansion board
|
|
Here is an update: I added an external power supply for the servos. Same problem. Everything works fine if I hook up to the charger in ZAP mode. Anyhow, I added an 0.22 microfarad across +5V and ground simply by sticking it into the headers on the (...) (25 years ago, 7-Jan-00, to lugnet.robotics.handyboard)
|