 | | You are not authorized to view this page
|
|
Hi! Trying to move to pages (URL) gives an "You are not authorized to view this page" error message. Anybody, have some idea what's going on? (25 years ago, 9-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: best HB kit source?
|
|
Hello Jeff, Acroname now sells the HB kit. Looks to be better than Peter Hui's kit, and it includes IC 3.2 in the $220 price. (URL) don't have the expansion board that handles LEGO powered sensors and has servo drivers, but Douglas Elect. has the (...) (25 years ago, 9-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: best HB kit source?
|
|
Check out (URL) luck! (...) ===...=== Kam Leang University of Utah Department of Mechanical Engineering MEB Room 2202 Salt Lake City, Utah 84112 ===...=== (25 years ago, 9-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: best HB kit source?
|
|
Jeff, Check out (URL) They have Handy Board kits, and lots of other things. I work with the owner, Steve Richards, quite often, and they have a first class operation over there. Plus, the price is right. Good luck, Gary Livick (...) (25 years ago, 8-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | best HB kit source?
|
|
I want to build a handy board kit and am looking for the best source. advice? -Jeff (25 years ago, 8-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Excessive clutziness when replacing the NiCad battery
|
|
Bill ... For spare batteries, take a look at B.G.Micro's BAT1024. They are two AA cells in series, 800mAh ... 10 batteries (20 cells) for US$5.95. I've made several spare HandyBoard battery packs using these cells ... and they all work great. (URL) (...) (25 years ago, 8-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Excessive clutziness when replacing the NiCad battery
|
|
Hello, everyone: Many thanks to Chuck McManis and Nick Taylor for posting the simple and elegant solution to my problem: install an inline plug Gee, I wish that I had thought of that!. Thanks for the help. Bill Bynum (25 years ago, 8-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | H-bridge chips
|
|
1. Two quick question, when i type 'ps' at the C prompt, i always get the following: PID STAT PC SP ORG Tricks Executing 1 20 c200 fe01 fe00 10 <command line interaction> is that there becoz Interactive C is running or is that something else? 2. my (...) (25 years ago, 8-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Excessive clutziness when replacing the NiCad battery pack
|
|
Hello Bill ... Here is what I've done on both of my HandyBoards and it's given good results. Cut the leads between the board and the battery pack and add 2-pin polarized connectors. Good luck and have fun, - Nick - (...) (25 years ago, 7-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Excessive clutziness when replacing the NiCad battery pack
|
|
Hello, everyone: I'm having problems when I replace the HandyBoard's NiCad battery. I have probably replaced around 10 battery packs by now on different HandyBoards. On 4 or 5 of the replacements, I end up having to replace the 74HC373 latch, (...) (25 years ago, 7-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | synchronization error
|
|
I'm encountering a synchronization error when calling serial_putchar within a for loop. Here's my code: void test(){ int looper; for (looper=0;looper<16;looper++){ if (looper<7){ serial_putchar(analog(looper)); printf("\nPort: %d Value: (...) (25 years ago, 7-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Another chance for the LM35
|
|
(...) Well, di you try to put an Operational Amplifier mounted in voltage following? +Vcc --- Op. Amp. | *-------* LM 35 O------|+ Vin | | | Vout|--\----- To 68HC11 Analog Port --- /-|- Vin | | GND \\\ | *-------* | \---...---/ Florent (25 years ago, 6-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Stepper motor
|
|
Does anybody know whether it is advisable to control a 24VDC stepper motor using the handyboard's motor outputs (11V)? also, what's the maximum phase current the motor can have to be compatible with the handyboard? (25 years ago, 6-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Stepper motor
|
|
Does anybody know whether it is advisable to control a 24VDC stepper motor using the handyboard's motor outputs (11V)? (25 years ago, 6-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | IR files and sensors
|
|
Two question i have: 1. On the Handyboard webpage, there're the files for the IR Remote Control software. it's a little long and complicated. i'm purely interested in activating the output ports and modulating it to transmit the 40khz signal and (...) (25 years ago, 6-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Another chance for the LM35
|
|
Hi, I'm again trying to connect the LM35 from National, there was some posts in the list, but none of that solve my problem. As an introduction let me say that the sensor provides an output of 10 mV/ ° C at 10 mA, the conversion when reading it (...) (25 years ago, 6-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | IC Technical Support problem
|
|
Hi! I bought my first handyboard in mid October and a Rug Warrior Pro in early November. And since I have had this peculiar download problem with the IC 3.2, pcode will download without any problems but everytime after downloading the lib files, IC (...) (25 years ago, 5-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: strange TS-53 servo problem
|
|
Hi ... It sounds as though you are obtaing the power for your servo from the HandyBoard's motor output pins ... and if so, this is the source of your problem. The HB does NOT control motor speed by varying the DC level ... it uses PWM to reduce the (...) (25 years ago, 4-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | strange TS-53 servo problem
|
|
Since the output ports for the motors of the handyboard supplies 11V, i connected a 5V regulator to power my servo. i have a capacitor between the driver's + and - terminals. I looked at the control signal on the oscilloscope. The duration of the (...) (25 years ago, 4-Dec-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Virus
|
|
Hi - Yes very well said -- on top of that HE may have been infected and we were the result of that infection. Sure can't see a guy putting out a virus with his name address phone and photo on it unless he is some really sick sucker! Regards - Dave (...) (25 years ago, 4-Dec-99, to lugnet.robotics.handyboard)
|
