 | | Handy Board help page
|
|
Check out this link... (URL) (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Parts List
|
|
I believe The Robot Store sells the kit for $170...but not including the Expansion board. Check the HB site for the site. (...) (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | bad GP2D02 link
|
|
What's wrong with Barry Brouillette GP2D02 Home page?? The link: (URL) the main Handybord Page won't work. I get an error message: employees is invalid. Has anyone the correct link or saved the pages&icb local? thank you (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | exp.bord analog routed trough 5&6?
|
|
Unfortunately I ruined my analog ports 0-3. Is it posible to route the expansionboard analog ports through port 5&6 of the handyboard instead of 0&1?? What do I have to do?? thank you Stephan (25 years ago, 7-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | A good toy to hack for the HB?--TIA
|
|
Hello all, The school year's starting and I need to commence my annual science project. I wanted a good RC car to hack. The LEGOs aren't sufficient. I don't need speed at all, actually I'd rather it be slow but I can always gear it down. But I would (...) (25 years ago, 6-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Use of GP2DO2
|
|
The problem could be in the power circuitry. Are the motors powered from a separate supply ? You could try placing some capacitors between the sensor's power connectors. Ronald -----Original Message----- From: Javaid Iqbal (...) (25 years ago, 6-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Use of GP2DO2
|
|
Hi all, I am using two GP2DO2 on Rug Warrior. Sensors are giving me very stable reading when motors are not running, but when motors are running the readings start jumping around. I am running the motors but the robot is static as I have placed it (...) (25 years ago, 6-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Thank you
|
|
Turns out I just needed a common ground between servos and HB Thanx all! :) Alex (25 years ago, 5-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: servo problem increased
|
|
Alex, My servos shutters when I first hooked them up but it was because the values were out of range. My servos work well in a range of 700 to 3800. Bye, Terry-----Original Message----- From: Alex Stewart <robotman5@hotmail.com> To: (...) (25 years ago, 5-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Parts List
|
|
I have just helped 12 people build up the handy board with expansion board at a cost of 165 each. But I live in the Heart of Silicon Valley. I was able to get board and all but five components locally. Those were the 68HC11, LCD, 470 cap, inductor (...) (25 years ago, 5-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | servo problem increased
|
|
Me again Now when I give servo_a5 or a7_init(1); the other servo shutters and nothing happens , when you unhook the sevo your not trying to drive the one you are kicks up but you can olny get it in varying speeds in one direction. Is it possible (...) (25 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Parts List
|
|
I should have phrased it better. I am a third year electrical engineering student and am trying to teach a class of twenty High school kids some basic electrical work in an after school project. I wanted them to get the experience of working with (...) (25 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Servo Problem! ???
|
|
Hi All The talrik bot running of a HB is doing serverly wierd things. I'vew tested these servo's on a old RC Reciver and they work fine , and my handy board can drive other servo s fine(not hacked thoe) Problem is when I give servo_a7_init(1); the (...) (25 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Parts List
|
|
It would be cheaper to buy it in kit form. If you try to collect the parts it may wind up more expesive due to shipping...depending on how n\many places you gotta go to...and also, availability, hunting the parts down, etc. This method is the worst. (...) (25 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Parts List
|
|
Do any of you have a more informative parts list? (Or did I miss it on the ftp site?) I am looking at buying the gear to build 25 handyboards for a High school project and need to find out if it would be cheaper to buy/ have the parts donated or (...) (25 years ago, 4-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Linux for the HandyBoard
|
|
Where are you located? I have a bunch of 486 Digitals that I am trying to get rid of. If you are in the boston area you could come by and get a 486 and a 14" monitor for 40 bucks. Or you could go to the MIT flea market and get about the same thing (...) (25 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | RE: SOLDER
|
|
Hi, I tend to use 22 SWG multi core solder for all my soldering jobs, and find it works for me. Russ.. -----Original Message----- From: Paul DaCosta [mailto:germano@voicenet.com] Sent: Friday, September 03, 1999 2:01 PM To: Handyboard Subject: (...) (25 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Linux for the HandyBoard
|
|
thanks I maily wanted it for building a cheap, viable Linux platform without having to delve into a somewhat-costly PC/104 board or the like... does anyone know of a cheap pc/104 or other small 486-based board available? thanks, --phil Phil: Check (...) (25 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | SOLDER
|
|
WHAT'S THE BEST "SIZE" SOLDER TO USE WHEN SOLDERING A 28 GAUGE WIRE (MOTORS AND SENSORS) TO A MALE PIN! (25 years ago, 3-Sep-99, to lugnet.robotics.handyboard)
|
| |
| | Any have a BS11 there willing to part with?
|
|
Hi I know this is'nt a HB ques , but , Does anyone have a BS11 that theyed be willing to part with , or know somewere they can be uptained relitvely CHEAP Thanx -- Alex (25 years ago, 2-Sep-99, to lugnet.robotics.handyboard)
|
