 | | Re: Increasing current output to motors on HandyBoard
|
|
So that's like $28 for the H excluding the protecting circuitry? How much did this setup cost for both motors? ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Increasing current output to motors on HandyBoard
|
|
Howdy, My original suggestion was to use *solid state* relays. They don't have any contacts. I use them plugged right into my Rug Warrior board at the motor output ports (would work the same on my Handy Board, but I have it on a smaller base, and (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Increasing current output to motors on HandyBoard
|
|
Haven't actually tried it, but I was thinking of the same sort of thing. Use a FET for PWM and a DPDT relay for direction. practically speaking, if you only switched the relay when the FET was off, no power transition, etc.... If your 'bot moves (...) (25 years ago, 10-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | GCC/HC11 small patch
|
|
I contacted the original person who did the HC11 port to gcc (Otto Lind), and he pointed me to a patch for it. If you're using gcc-2.8.1 with the HC11 patches in it, you may want to try this: At line 502 of config/m6811/m6811.c, change from: { (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) You can have a copy of mine if you like. You can relocate it to any available digital ports with ease. It is set up for a single sensor, but you can easily add as many as you have ports for. (...) For people using the Handy Board in small (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) I think I'm in the process of writing up such a document. Combined with Fred's guide to programming the 6811 (which covers the miniboard nicely), hopefully this will fill the gap. (...) And using IC libraries works well, up until you have a (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: GCC 2.8.1 for HC11
|
|
(...) You have to get good at reading schematics in this case, period. Schematics are very hard to read at first, but it does get easier quickly. If someone were to write up details on how to access various devices on the Handyboard though (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Vesit rover
|
|
Dear friends, You know that we at Vesit, Bombay were making a rover using the handy board. Learn more about it at (URL) sincerely, Nitin (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Multi-Processing
|
|
Dear Kat, Try using music.c that I had downloaded and I have sent as an attachment.This file cantains functions which play music on the piezobeeper. Yours sincerely, Nitin (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
| | Re: PCB coating
|
|
First use TINNIT Bright Tin Plate No. ER18 (cheap and does the job) available at Circuit Specialists and Jameco. A better tin plate already mixed can be found at JDR Micro Devices. Then use M.G. Chemicals Conformal Coating which is a flexible (...) (25 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
