 | | Re: Rolling Ball Inclinometers
|
|
(...) It's All Electronics. 2 for $1.00. 1.800.826.5432. Page 17. Catalog numbers ATS-1 and ATS-3. No real specs for them, but both are pulls from arcade games. (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Linux, and HB beta binaries
|
|
I've run it on Red Hat (5.2, stock Glibc) and I'm running it now on Slackware (3.6, stock). I haven't had any problems either, but I built it from source as well. (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Linux, and HB beta binaries
|
|
Hi Edward, I am running ic on linux since December. I downloaded the _SOURCE_ from the same location as you I think, (ic-src-unix-2.860-beta.tar.Z) and build the binaries on my system to make sure they will use the libraries I have. You also have to (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | 3 used HB
|
|
During the last few days I have received more then 40 offers to buy my 3 used HBs. I am almost done selling the HBs according to the criteria of geographical convenience. I am sorry for all the other people that answer to my letter. ---...--- (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Rolling Ball Inclinometers
|
|
Does anyone know of a place to get cheap rolling ball inclinometers? thanks Michael (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Linux, and HB beta binaries: problems getting started
|
|
Handy Board list: I'm trying to get the handy board running under Linux for a robotics class at the University of Colorado. All the devel platforms are Macs but I'd like to use Linux. I'm having problems getting started, even though I've grepped all (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Could IR ranging sensors be used with Rug Warrior board as we ll
|
|
Hi, I can only speak for the GP2D02: voltage requirement 5 volts very low power range 10cm to 80cm beam width at maximum range is about 1cm 1 input bit and 1 output bit required Cheaper,smaller ,less power, and easier to hook up than sonar I see it (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Two servos, one input ?
|
|
Has anyone hooked two servo motors up to one input? I have a project that requires three servos, but two are an identical pulse. I was going to hook those two up as servo_a7 and run a 1000-1200mA current at 6 volts. I'm thinking that will give me (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Could IR ranging sensors be used with Rug Warrior board as well
|
|
Hello all: I have to ask this question: I am using a Rug Warrior Pro board and handyboard. Could the Sharp GP2d02 or the Hamatmtsu P5507 be used on the Rug Warrior as well. More specifically : What are the voltage requirements of these two? What are (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Power problems?
|
|
To all: I am currently constructing a Handy Board. Am I currently at the step (with the Handy Board) of testing it with the Interface/Charger board. The tests I performed earlier on the charger worked, and the tests so far with the Handy Board have (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
