 | | Linux, and HB beta binaries: problems getting started
|
|
Handy Board list: I'm trying to get the handy board running under Linux for a robotics class at the University of Colorado. All the devel platforms are Macs but I'd like to use Linux. I'm having problems getting started, even though I've grepped all (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | RE: Could IR ranging sensors be used with Rug Warrior board as we ll
|
|
Hi, I can only speak for the GP2D02: voltage requirement 5 volts very low power range 10cm to 80cm beam width at maximum range is about 1cm 1 input bit and 1 output bit required Cheaper,smaller ,less power, and easier to hook up than sonar I see it (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Two servos, one input ?
|
|
Has anyone hooked two servo motors up to one input? I have a project that requires three servos, but two are an identical pulse. I was going to hook those two up as servo_a7 and run a 1000-1200mA current at 6 volts. I'm thinking that will give me (...) (26 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Could IR ranging sensors be used with Rug Warrior board as well
|
|
Hello all: I have to ask this question: I am using a Rug Warrior Pro board and handyboard. Could the Sharp GP2d02 or the Hamatmtsu P5507 be used on the Rug Warrior as well. More specifically : What are the voltage requirements of these two? What are (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Power problems?
|
|
To all: I am currently constructing a Handy Board. Am I currently at the step (with the Handy Board) of testing it with the Interface/Charger board. The tests I performed earlier on the charger worked, and the tests so far with the Handy Board have (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Hamamatsu P5587
|
|
I'm not an ASCII artist, so I'll attempt a verbal description. View the P5587 with the emitter/detector side facing you and have two pins on the left and three on the right. In this position pin-1 is in the upper left corner, pin-2 in the lower (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Hamamatsu P5587
|
|
Does anybody have the pinouts or spec sheet for the Hamamatsu P5587 optical sensor? Thanks (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Sharp GP2D02 code available
|
|
Thanks Barry, great work. I do have one little question: As I read the data sheet of the GP2D02 ( (URL) ) I saw some timing specifications that i think are not taken care of in your software. Please correct me if I'm wrong. The timing chart shows (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Precise timing with the Handyboard ?
|
|
(...) Use the TIC port 2 or 3. The precision of the reading you'll get is 0.5 us. About a year ago I posted some drivers to make such measurements. Tell me if you want them. cu Tom -- Thomas Hauri ZHW Zuercher Hochschule Winterthur University of (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
| | Precise timing with the Handyboard ?
|
|
Hi, does anybody know how to measure the time between two trigger signals as precise as possible ( around 10 microseconds would be fine.) with the handyboard. Peter -- Dr. Peter Borrmann University of Oldenburg Phone: +49 441 798 3362 (office) (...) (26 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
