| | Re: How to disable ROM on E9 part?
|
|
I hate replying to my own posts, but I think I know a bit more about the problem now, therefore different questions are in order. Answer to my first question: It looks like the HC11 is supposed to automatically clear the EEPROM, CONFIG, and RAM if (...) (28 years ago, 1-Jul-96, to lugnet.robotics.handyboard)
|
|
| | Ordering of handy board.
|
|
Maybe this is an off topic but ... I ordered a handy board to Digital Microsystems about 5 weeks ago and I still know nothing about it. I just wanted to ask (in case any of you have experience dealing with this supplier) how long does it usually (...) (28 years ago, 1-Jul-96, to lugnet.robotics.handyboard)
|
|
| | How to disable ROM on E9 part?
|
|
Help! I'm trying to get my handyboard to go into download mode via the STOP/Power-On sequence, and it doesn't go into the correct mode. The PWR LED doesn't go out when I do this sequence. Have tried downloading with DLM, HBDL, and DL to no avail (...) (28 years ago, 1-Jul-96, to lugnet.robotics.handyboard)
|
|
| | cher is up again
|
|
but the incoming directory is disabled. i don't see any way around this problem; if there are incoming directories, it seems this gang of crackers will find them. i would still like to encourage people to contribute robotics related stuff, but it (...) (28 years ago, 1-Jul-96, to lugnet.robotics.handyboard)
|
|
| | cher is shut down until further notice
|
|
until i figure out how to disable the incoming directory from crackers. -Fred (28 years ago, 1-Jul-96, to lugnet.robotics.handyboard)
|
|
| | timer flags
|
|
The timer flags are cleared by either loading the accumulator with the bits you want cleared and then storing them in the timer flag register, or by using BCLR with a complemented mask. -Dirk "I speak from experience" (28 years ago, 29-Jun-96, to lugnet.robotics.handyboard)
|
|
| | (no subject)
|
|
In regards to the bit manipulations of the timer flags... I concede. At this time I have neither the mental capacity nor the desire to figure out what is correct. After copying the paragraphs earlier, I am only sure that the documents could use some (...) (28 years ago, 29-Jun-96, to lugnet.robotics.handyboard)
|
|
| | Re:
|
|
(...) Lyle, The following provide PLCC-to-breadboard adapters: Amaze Electronics Co. Tel: 1-800-996-2008 Web: www.hooked.net/users/amaze Technological Arts Tel: 1-416-963-8996 Web: www.io.org/~techart You can see their ad on the July 1996 issue of (...) (28 years ago, 29-Jun-96, to lugnet.robotics.handyboard)
|
|
| | Re: your mail
|
|
(...) Very confusing, especially since at the beginning of the same file, there are the lines: * Setup Interrupt for Encoders * LDX #BASE BSET TCTL2,X %00001100 /* Interrupts TIC3,TIC2 rising edge*/ BCLR TFLG1,X %00000010 /* Clear IC3,IC2 Flags */ (...) (28 years ago, 28-Jun-96, to lugnet.robotics.handyboard)
|
|
| | hb basic questions.
|
|
Well this is my first post and my first look at the handy board. I have a couple of basic questions, sorry if this is maybe asking for the obvious but I didn't find answers to these on the web nor in the archive. Anyway thanks already for all and (...) (28 years ago, 28-Jun-96, to lugnet.robotics.handyboard)
|