 | | Re: How to measure the signal Voltage ?
|
|
not knowing anything about the sensor, but guessing (hoping) that it behaves like an open collector gate, this is what i would do--fool with the sensor on the bench to determine how it works before i let it near the HB. 1. power up the sensor, (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Print to LCD
|
|
I certainly do! Spent a lot of effort working developing a machine code interface for the Handyboard. One of the biggest hurdles was getting messages to the LCD display. If you look on the Handyboard home page, in the contributed section: (URL) will (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Parts availability
|
|
(...) I was able to follow the parts list and get most of the things from the suggested supplier. (...) (eqivalent?) (...) I thought that I got the memory from Jameco, but I think BG-Micro sells it was well. I would also think they both might carry (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: IR outputB
|
|
Is the IR reciever on the HB the same thing as in the robot in MR:ITI book? I though it would be different. In any case, you can but...the reciever is more effective as a "wireless communication" device that can recieve various IR codes which you (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: IR outputB
|
|
(...) o Hi Did anyone receive an answer to this. I ant to connect a Radio Shack (276-143) IR LED to the IR output and am wondering what resistance to use. Also, I saw a design in Mobile Robots..Inspirition where they use two IR LED (one on each (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Parts availability
|
|
To all: I am constructing the Handy Board from 'scratch', since many places want upwards of $200 for a built (and tested) board. I have located most of the required parts, but have not located the following: the 1 uH iron core inductor the 5W 47ohm (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | How to measure the signal Voltage ?
|
|
Hi Everybody, I am using the retroreflective sensor to an object . The sensor is came from Masushita NAIS brand name. It has 3 wires . ONe for the +ve supply , one for the -ve supply, one for the output signal line. The sensor is using a NPN type. (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Print to LCD
|
|
Hi everyone, Does anyone know how to print messages to the LCD in assembly language. Thanks (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | RE: External Motor Power and the Expansion board.
|
|
I noticed this to when I built mine, I just bridged the gap I had cut with solder and now use an H-bridge to control the motors. Clancy (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Problem resolved?
|
|
To all, Regarding my previous... I am not sure if it was a soldering connection, but after retesting the output voltages it is very close.. Fred says that the voltages should be between, say, +9 and +10, but I'll get a 8.7.. Is this good enough? If (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
|
