 | | Re: Expansion board questions
|
|
Hi Duncan, I would like to have a copy of your hbtest.c to test the expansion board. If you could post it I bet a lot of us would use it to test. Thanks in advance Terry G. ---...--- (...) doesn't (...) which (...) the (...) the (...) height (...) I (...) (26 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Serial Communication Please Help!
|
|
Hi, I am trying to get communication working between two HBs via the RJ11 serial port. I read the FAQ on the HB web site and I have the right cable. On the trans. HB the power LED blinks which indicates it is transmitting. Also whenever I turn on (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | I2C bus with the Handy board ?
|
|
Hi! It is possible to use component with I2C bus on the Handy board ? Do you know this ? some examples : PCF8584, PCD8574, PCF8591...... I'd like to use many component with this bus. Can you help me (if it is possible) ? thanks Dperonne@aol.com (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Stepper Motor
|
|
(...) You can get some from old printers or scanners but I think they are rated for 24V (...) For Eurobot 97 ,some robots were using stepper motors. On Internet, there was also a guy who explained how to build a robot from a floppy drive. As far as (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Stepper Motor
|
|
I am also trying to use steppers motors from an old floppy, if anyone has accompished this I am interested in your result and methods Keith (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Stepper Motor
|
|
Hi, I have a question. Can i use stepper motors to drive my robot platform ? Do i need a gear ? I'd like to use stepper motors instead of normal ones, because I would not need any shaft encoders. And I think stepper motors do not cause so much noise (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | IR Emmiter and Detector for RW Pro
|
|
Hi All, IR emitters and detector used on Rug Warrior Pro are LTE-4206 and IS01U60 respectively. Can any body help me out, from where I can get their data sheets? Are these still available with any stockiest if not what are the best alternates? (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | serial_getchar(int c) what's int c for?!
|
|
in serialio.c from Randy what is int c for when you're recieving characters from the serial line? Can you just transmitt 8-bit intergers over the serial line or can you transmit bigger numbers? -Peter (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: HB and V8600 module??
|
|
Here's a link: (URL) - - Nick - - - (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
| |
| | Re: ***sharp GP1U5 IR detector***
|
|
Mike - - Here is the Sharp data sheet page: (URL) fun! - - - Nick - - - (...) (26 years ago, 14-Feb-99, to lugnet.robotics.handyboard)
|
