 | | Re: HB and Acceleration
|
|
(...) I presume that you are not planning on using my infrared control software! Good luck in your project, it sounds like fun. Wanna tell us more about it? /Max (26 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | HB and Acceleration
|
|
Hello, Does anyone here know how acceleration will affect the operaion of a handyboard, and also will sudden changes in altitude (like, 3,000 feet in less than ten seconds) affect it's operation? I have a High Power Rocketry launch coming up in May, (...) (26 years ago, 11-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: Wireless Handyboard Link ?
|
|
-----Original Message----- From: Aaron Edsinger <aarone@sirius.com> To: handy <handyboard@media.mit.edu> Date: Sunday, January 10, 1999 1:04 PM Subject: Wireless Handyboard Link ? Hello, I am investigating createing a wireless serial link between (...) (26 years ago, 10-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: buying IS1U60, DS1233-10 in germany
|
|
a reseller for the IS1U60 is RS rs-gmbh@rs-components.com FAX 06105/401-100 Hessenring 13b 64546 Mörfelden-Walldorf a reseller for the DS1233-10 is FARNELL FAX 089/6135901 Grünwalder Weg 30 82041 Deisenhofen bei München I hope it helps ... SR. (26 years ago, 10-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | buying IS1U60, DS1233-10 in germany
|
|
Does someone know a reseller in germany who sell the IS1U60 and/or the DS1233-10 (just one of each) ? thanks for reply (26 years ago, 10-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Failure to Boot Up
|
|
I recently purchased the Handy Board 1.2 and am running the HC11E1FN. I also purchased the IC compiler from Newton Research Labs. Everything worked great. I hooked up a hobby servo to PA7 and it ran well with the supplied c routines. However, after (...) (26 years ago, 9-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: A newbie question
|
|
if your robot is not allowed to even partially cross the duct tape, you must have an additional inner marking that the robot can see so it knows it's near the "danger zone" and can change direction. f. (...) (26 years ago, 9-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: supplier for Sharp IS1U60 infrared demodulator
|
|
All- Ok, I'll re-phrase..... Does anyone have the name and supplier of a substitute (for the Sharp IS1U60 infrared demodulator) that they have gotten to work reliably? Thanks. Steve (...) (26 years ago, 8-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | A newbie question
|
|
I want to program my HB so that my robot will be able to navigate around obstacles. The navigation area is a rectangular area boarded by a silver duct tape. My robot shall not touch the tape. Does anyone have any idea of how I can implement this? (...) (26 years ago, 8-Jan-99, to lugnet.robotics.handyboard)
|
| |
| | Re: hexipod walker
|
|
Timing 12 servos with the HB could be done. So far we are using 8 servos which don't use much cpu resources at all. But 1 compare output can only time 8 servos because of the servos timing requierments without using a lot of cpu time. So a second (...) (26 years ago, 8-Jan-99, to lugnet.robotics.handyboard)
|
