| | help needed for ir sensors & memory addressing latch
|
|
Hi all, I am new to robotics and have great difficulty trying to get the near-infra emmiter and detector on the HB to work properly. After studying the schematics, I figured out to activate J7, I should do a bit_set(0x1000,0b01000000) which appears (...) (26 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Re: Steppers
|
|
Dear Terri, If the motors turn sparatically, that means the coils are probably not hooked up in the correct order. Try swapping them around and see if anything improves. The motors you are using are the bipolar type. There is a decent way of hooking (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Re: Serial line interrupt
|
|
(...) to (...) about (...) Hi, you could simply build and Acknowledge routine so that every character sent by the PC could be echoed back by the HandyBoard. It asks a bit more of processing time from the HandyBoard, but at least it's simple to build (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Steppers
|
|
Hi. I was reading through a compilation of emails from the Handy Board Q&A and found a lot of great questions, but no answers to them. I am trying to power some steppers, microsteppers from the RobotStore catalog, with the HB and am not having much (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Re: Serial line interrupt
|
|
(...) I had the same problem a few weeks ago, ended up writing an interrupt handler for the Handy Board which will buffer up the incoming serial information so that none of it is lost. I guess the Handy Board normally just polls the serial port (I (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | using the MC34064 LVI
|
|
Hello, This is a warning for anyone considering using the Motorola MC34064 to replace the DS1233. I have just built a couple handyboards and I had some problems getting them working. I finally tracked the problem done to the LVI. I used the MC34064 (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Serial line interrupt
|
|
Hello all, I'm currently trying to communicate between the Handy Board and a PC (i486) using the existing serial line between the two. Sending data from the handy Board to the PC is no problem. An interrupt handler puts all incoming serial data into (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Connecting radio module (BiM 418 F)
|
|
Hello all, I would like to be able to 'drive' my robot using the Handy Board via a radio link. For this purpose I have bought two transceivers, the Radiometrix BiM 418 F. How can I connect it to my Handy Board? The wiring is as follows (leaving out (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | Stepper motor
|
|
Hi, I trying to make a home page about interfacing handy board with stepper motors, I hope it has enought quality to add a little contibution to the handyboard effort. For now I has just two part : One is just mails I found in the mail archive about (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
|
| | test
|
|
thanks for ignoring this message! Sorry, but I have not been getting sny HB messages for a week, and I wanted to see if it was a problem at the HB end or mines. Thanks! phil (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|