 | | using the MC34064 LVI
|
|
Hello, This is a warning for anyone considering using the Motorola MC34064 to replace the DS1233. I have just built a couple handyboards and I had some problems getting them working. I finally tracked the problem done to the LVI. I used the MC34064 (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Serial line interrupt
|
|
Hello all, I'm currently trying to communicate between the Handy Board and a PC (i486) using the existing serial line between the two. Sending data from the handy Board to the PC is no problem. An interrupt handler puts all incoming serial data into (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Connecting radio module (BiM 418 F)
|
|
Hello all, I would like to be able to 'drive' my robot using the Handy Board via a radio link. For this purpose I have bought two transceivers, the Radiometrix BiM 418 F. How can I connect it to my Handy Board? The wiring is as follows (leaving out (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Stepper motor
|
|
Hi, I trying to make a home page about interfacing handy board with stepper motors, I hope it has enought quality to add a little contibution to the handyboard effort. For now I has just two part : One is just mails I found in the mail archive about (...) (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | test
|
|
thanks for ignoring this message! Sorry, but I have not been getting sny HB messages for a week, and I wanted to see if it was a problem at the HB end or mines. Thanks! phil (26 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: data acquisition
|
|
yes, you can write a program for IC to print the information to the serial line. see the FAQ for information about using the HB serial line from an IC program. Fred In your message you said: (...) (26 years ago, 5-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | ds1233-10
|
|
Can anyone recommend a good supplier for the ds1233-10 (or MC34064) and also the IS1U60??? Thanks in advance.... Owen (26 years ago, 5-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Uploading arrays
|
|
Dear All I intend to log the data from up to seven analog inputs, and 2~3 digital inputs, in an integer array every minute for up to an hour, and then upload the data to the PC and import it into MS Excel. 1) Could anyone point me to any IC software (...) (26 years ago, 5-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | data acquisition
|
|
this message is especially for Fred Martin: is there any way to retrieve a large integer array (1000 or so elements) from the handyboards memory, and save it in a file on the PC? thank you. Justin D. Gullotta.. , Engineer, Rensselaer Polytechnic (...) (26 years ago, 5-Jul-98, to lugnet.robotics.handyboard)
|
| |
| | Re: 7-Segment multiplexing
|
|
There are plenty of seven seg driver chips out there that you can connect to the HB. Look some up on the web (data sheets are all over the place! try a search engine). I have experience with a nice chip that drives four seven segs with serial input, (...) (26 years ago, 4-Jul-98, to lugnet.robotics.handyboard)
|
