 | | 5mm range reflectance sensor
|
|
Hello, I've got a 5mm range reflectance sensor which I am trying to get to work with the handyboard, without much success. Here is what I have: DigiKey part #: OR506-ND Manufacturer #: EE-SB5V The labels on the leads are as follows: .--- (+) .--, / (...) (29 years ago, 8-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | announcing the HB Expansion Board version 2.0!!
|
|
Greetings all, The Handy Board Expansion Board version 2.0 design is complete! I'm pretty excited about the feature set, which includes a bunch of things not on the older (not released) expansion boards: * high-impedance analog inputs * PIC (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Caster Substitute
|
|
While there is some discussion on robot bases, let me add a bit about the "third wheel", usually a caster, used on differential drive systems. Casters have the advantage that they are plentiful, cheap, and come in lots of sizes and configurations. (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Using cheap RC chasis as 'bot
|
|
I used a Fischer Price RC car: well built with two gear settings and quite battery efficient. Once the RC receiver was ripped out, there was plenty of space for the Miniboard to be mounted internally. However, I chose to mount it on top in a (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: battery voltages
|
|
(...) I'd use 6V instead of the 9.6V main power supply - connect it where the main battery terminals are. It'd be really nice if the handy board had a way to use voltages other than 9.6V for the motor driver chips, ya know. :-) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Robot Chassis
|
|
Given the extensive traffic concerning robot platforms, I thought I'd add my two cents: For my senior project at Cal Poly I made a robot that had three wheels, two of which were independently driven and one which was a small caster. The chassis and (...) (29 years ago, 7-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: battery voltages
|
|
(...) Yes, and the current capacity would be the same, since excess voltage gets dissipated in the HB's voltage regulator. -Fred (29 years ago, 6-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | battery voltages
|
|
Regarding the use of a 6V ni-cad pack to solve my over-voltage problem in driving small motors, could I still use my current 9.6V pack, but simply insert a tap into the battery at somewhere close to 6V? Seems nicer than buying another battery pack, (...) (29 years ago, 6-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | RE: Connected Radioshack truck
|
|
(...) You know what makes REALLY good REALLY cheap shaft encoders? Mice! Get an old mouse that has a broken button (that's usually what goes on mice) and pull it appart. Sometimes, depending upon the kind of mouse, you can get really luckey, and be (...) (29 years ago, 6-Feb-96, to lugnet.robotics.handyboard)
|
| |
| | Re: Connected Radioshack truck
|
|
(...) (snip) (...) I also have one of the Radio Shack RC trucks. A good solution for shaft encoding would be to glue a couple (or 4) magnets to the inside rim of the rear tires. Then glue a hall effect sensor to the axle. When the wheel spins, the (...) (29 years ago, 6-Feb-96, to lugnet.robotics.handyboard)
|
