 | | RE: Wireless Communication with HB
|
|
My goal is to read various input devices ie joystick, keyboard, etc. encode the data into some sort of bit or ascii stream and then transmit it to the HB for decoding and if possible transmit from the HB back to the PC for telemetry such as (...) (27 years ago, 28-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Serial Device Interfacing
|
|
B> It will be used to control a LM197x digital Attenuator which has a B> 3 wire serial interface. B> Is it possible to wiggle the output lines in such a way ? Any B> hints ? If it is a 3 wire interface, does this imply synchronous? That sounds like (...) (27 years ago, 27-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Error in bootstrap mode
|
|
Dear Sir I start a Handy Board assembly and till now my board has passed the following steps : Microprocessor Power Circuitry ---- Passed Voltage Monitor Chip ---- Passed Microprocessor and Oscillator Circuit ---- Passed The problem focused at the (...) (27 years ago, 27-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Serial Device Interfacing
|
|
OK Newbie Allert !!! I'm looking at the Handy Board as a major step up from the Basic Stamp 2, but I need to be able to send out serial messages from the digital outputs. On the BS2 it is declared as a ShiftOut instruction. It will be used to (...) (27 years ago, 27-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | New E-Mail Address Notification
|
|
Update your records! Customer BERND KLEIN has recently obtained a new e-mail address from NET@DDRESS a service of USA.NET. You can now reach this person via e-mail at bernd.klein@usa.net. This change is effective immediately. If you would like to (...) (27 years ago, 27-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | HB site and 2.x web browsers
|
|
So all of my work is incompatible with version 2.x browswers, which don't colorize text. As an interim solution, I have created a site index page -- a single page that points to all pages linked from what are invisible menus if you have a 2.x (...) (27 years ago, 27-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | RE: Wireless Communication with HB
|
|
Are you wanting to transmit an analog signal, e.g. faster/slower, such as most people do with a joystick, or some other purpose? Did you want the PC to generate the signal, or a standard RC transmitter receiver? I've used the HB Input Capture line (...) (27 years ago, 27-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | HB web site renovated!
|
|
Hi everyone, I've completed the HB web site's first major renovation, after about two years of existence. I'm pretty excited about the new look, which hopefully will serve the primary purpose of making information easier to find. it's there at the (...) (27 years ago, 26-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Wireless Communication with HB
|
|
I was wondering if anyone has attempted to transmit data from a pc to a HB device using a standard RC transmitter and receiver. My goal is to be able to control an HB driven robot using a PC's joystick. Any help or suggestions would be greatly (...) (27 years ago, 26-Oct-97, to lugnet.robotics.handyboard)
|
| |
| | Motor drivers
|
|
Hi, I recently assembled a Handy Board and some of my motor ports don't work. With the first driver chip, motors #0 & 1, the LEDs turn on but there is no current coming from the headers. With the second driver chip just motor #2 doesn't work. Can (...) (27 years ago, 25-Oct-97, to lugnet.robotics.handyboard)
|
