 | | Re: LM34 temp sensor to handy board?
|
|
Jeff, I used a couple of the 10mV/deg Kelvin ones, with nothing more than the current load resistor, ie no amplification at all. For example, freezing point = zero celcius = 273 Kelvin = 2.73 volts. With the 6811 resolution of about 20 mV (5v / (...) (27 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | headers
|
|
This may sound like a dumb question, but I don't know where to get headers. Digi Key has some but 4 different kinds. The parts list says nothing except 14 pin female header. Nothing else. Where did you get your headers and what are the part numbers? (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo control using Miniboard slaved
|
|
Chuck: I agree with you; what I've done with the MiniSSC is to break the path into a set of linear segments with via points in joint space. The lynxmotion arm ends up needing a lot of points (therefore moving pretty slowly) to avoid jerkiness, but (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: LCD display
|
|
(27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: LCD display
|
|
Hi. Give me the location and phone number to this place that you can order them and I will consider ordering several and selling them off individually. Scott sherman@plains.nodak.edu CSG ITS NDSU (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | LCD display
|
|
Hi there, I'm in the midst of ordering all of the parts necessary to assemble the Handy Board. However, I'm having trouble finding two parts. They are the following: Description Catalog No. Manufacturer ---...--- ---...--- ---...--- Infrared (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: FW: Serial Communications.
|
|
Hi Fred: The Mini SSC does have a TTL-mode, but it needs inverted data i/o mode. Rather than figuring out how to do that in s/w I just used the MAX232 because it was easy and it made debugging easy into a dumb terminal program on my PC. I've had (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo control using Miniboard slaved to Handyboard.
|
|
Using the Miniboard as a servo slave is a good idea, perhaps even easier is to use a BOTBoard since the BOTBoard doesn't have any motor drivers hooked up to it (no PCB modification required.) Using the MiniSSC is "ok" but for controlling multiple, (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: FW: Serial Communications.
|
|
Mike -- Doesn't the Mini SSC have a TTL-levels mode, making the MAX232 unnecessary? Please send your serial output code, though. that would be good to distribute. -Fred In your message you said: (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | FW: Serial Communications.
|
|
Hi John: I've used the HB to send serial command strings to a Mini SSC (for the Lynxmotion arm). I built a tiny daughterboard with a MAX232 that plugged into J6 on the board for power. Software handshaking is minimal and the MiniSSC works fine. If I (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Exp Board ETA?
|
|
I was wondering whether there was an estimated date for the availability of the said expansion board for the HB... there is a design and schematics for a proposed Exp Board on the web site from February and I remember a thread of discussion and (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | RE: Serial Communications.
|
|
Thanks for the info. I would like to see the code and wiring diagram if that's possible. Thanks for the help. John Hatton. (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo control using Miniboard slaved to Handyboard.
|
|
A friend of mine built a radio controlled walker with six legs using twelve servos and a single BASIC stamp to control the walking. The stamp accepts the PWM from the RC receiver (using the pbasic 'pulsin' command) and outputs the pulses to all of (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Servo control using Miniboard slaved to Handyboard.
|
|
As an addition to my earlier message I have a cheaper and possibly more versatile way of controlling the servos. I have obtained information on the Servo16 algorithm by Erik de la Iglesia which runs on a MC68HC11E1 (he mentions using the E9 but the (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Serial Communications.
|
|
I am considering using two MiniSSC II servo controllers from Lynxmotion ((URL) to control the servos on a six leg walker using the handyboard as the CPU. The only problem is that the MiniSSC uses asynchronous serial communication. Is it possible to (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: LM34 temp sensor to handy board?
|
|
I tried the circuit out tonight, and it works! (Mostly.) I hooked up a 1K and a 3K resistor for R2 and R1, for a gain of 4, and the output is roughly linear with the input. Still need to do some more testing. I ended up having to use a +/- 12V (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Geting Started?
|
|
Why don't you start by perusing the web site... pretty much all of your questions are answered there. The site's home URL is (URL) in particular: * the FAQ * the "get your hands on a handy board" * the software resources page * the tech docs page (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: LM34 temp sensor to handy board?
|
|
It sounds like you just want a standard non-inverting amplifier. wire an op amp like this: |\ sensor------|+\ | >-+-analog input of 6811 +--|-/ | | |/ | +----R1-+ | R 2 | GND where R1 and R2 are chosen such that (R1+R2)/R2 is the gain you want, in (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Geting Started?
|
|
Hi everyone, I am fairly new to robotics/electronics and was wondering how to get started with the HandyBoard. So what is the best way to get started? I already know how to program more or less in C and a little in C++ can you program the Handy (...) (27 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | LM34 temp sensor to handy board?
|
|
I've got on my desk here a National Semiconductor LM34 temperature sensor. It outputs a voltage corresponding to 10mV/deg F. So, if it's 78 degrees F in the room, I get a voltage of .78V. I'd like to hook this device to an analog port on my handy (...) (27 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
