 | | Re: voice synthesis
|
|
(...) Wow, impressive board. However, it's a bit out of my price range - I was hoping for a solution just about as cheap as the Radio Shack one used to be. Quality of speech isn't that much of a factor, I'm merely going to try and put this thing on (...) (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Svar: Trouble shooting 7.2.2 (The digital inputs)
|
|
Hej I'm had the same problem, until i found that I loaded some programs via lib-file, not suitably for HB. (lib_r22.c) It seems you are running some programs for the 6.270. Have You setup IC correct? Try run c:\IC -config. Check out your lib-files. (...) (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Future versions of handyboard?
|
|
(...) I suspect there probably aren't such plans. One of the problems is the amount of infra-structure needed for a successful board. Basically you need a good board and a good development environment, and you have to be as inexpensive as possible (...) (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | lcd and ds1233-10 supplier
|
|
Just for the record, I was able to get the Hitachi LCD and the Dallas Semi. voltage monitor from Sterling Electronics. Their number is (512)836-1341. This location is in Austin, TX, but I think that they have a 1800 number, though I don't know it. (...) (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Trouble shooting 7.2.2 (The digital inputs)
|
|
(...) Thanks, that fixed the problem. I am happy to find that the problem was just software. Anthony Oren Loeppert *** (URL) * o* * ***> * * * * * | | * * | / * * |/ * * * * * * **\ (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Trouble shooting 7.2.2 (The digital inputs)
|
|
you are using the wrong library file. configure IC to use lib_hb.c, not lib_r22.c. -fred In your message you said: (...) (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: HB and ICC11..
|
|
please post any answers to the board, as I also have ImageCraft's C compiler and have been as yet unable to set it up properly. thanks, -patrick (...) HandyBoard. (...) your (...) using (...) (27 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: HB and ICC11..
|
|
Howdy- I saw your posting on the HandyBoard list. I don't know if I have any LCD code laying about or not but I'll look and see. Meanwhile, I noticed in your letter that you indicated you were using ImageCraft-C with the HandyBoard. I was wondering (...) (27 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: HB and ICC11..
|
|
(...) The trick is to copy the mode-change/LCD code into the on-chip RAM and execute it from there. This code must change to single-chip mode, write to the LCD, then change back to expanded mode. When in single-chip mode, you lose access to any (...) (27 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
| |
| | Re: HB and ICC11..
|
|
Hi Dale, For this to work a couple of things have to be true, first the Start_LCD, Stop_LCD, and putlcdchar() functions have to be located in the 256 bytes of on-board RAM (or in the 512byte EEPROM) The second thing is that your putchar_LCD doesn't (...) (27 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
