 | | Out of memory error
|
|
Randy, Thanks for your help so far, but I have a few questions. How can I remove drivers to get more room. Where can I quickly get a copy of IC 3.1? And how much does it cost? -Joe (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Memory problems
|
|
I have been having big problems with the programs that I have been writing for my handy board. I currently have around 1400 lines. I expect to have about 2000 when I'm done. I have many functions called throughout the program and recently have (...) (27 years ago, 27-May-97, to lugnet.robotics.handyboard)
|
| |
| | Out of memory error
|
|
(...) At some point, you may run out of memory on the Handyboard; however, it sounds like IC 2.8 is running out of the 640K DOS-limited memory. You might try removing drivers to get more room in the lower 640K. If you move up to IC 3.1, which is a (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
| |
| | Re: clueless programmer
|
|
A very simple program which will exercise the motors in this configuration is listed. The first section will put a message on the LCD then wait until the sopt button is pressed. Once the stop button is sensed, it will turn on the motor in port 0. (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
| |
| | TEAC Stepper motor
|
|
Has anyone had any experience driving the stepper motor from a TEAC 5 1/4 in floppy drive with the HB. I have been going through Jones' tutorial on stepper motos and have decided that the motor is a permanent magnet, 4 winding variable reluctance (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
| |
| | RE: IC 3.1
|
|
also, joe... there are several programs you can run to get more conventional memory (640)... dos 6.0 to 6.22 comes with memmaker... run this a couple times, toy with the settings a bit to see what you can pull off... one of the settings may cause (...) (27 years ago, 26-May-97, to lugnet.robotics.handyboard)
|
| |
| | Motors: Please help! Going out of my mind...
|
|
Please somebody help! Actually it's not quite that bad, but I've been searching and hunting trying to find some motors to use for a new robot base. Does anyone have any suggestions for where to find motors with gearboxes that can carry a few pounds (...) (27 years ago, 25-May-97, to lugnet.robotics.handyboard)
|
| |
| | clueless programmer
|
|
Ihave only been working with my HB for a few weeks but the coding appears pretty easy. I'll be happy to help/teach you C. Which ports are the motors and touch sensor connected to. (...) (URL) (...) else for that matter. (...) Tutebot from (...) (...) (27 years ago, 24-May-97, to lugnet.robotics.handyboard)
|
| |
| | futaba compatible servos
|
|
hi... i'm coreyfro, (hi coreyfro) and i'm totally new to this... i'm a junior-programer/ele...-addept(or addict)/new-toy-junky i was drawn here via the lego aspect, but that is not my cocern now... i have buckets of radio controlled car junk at my (...) (27 years ago, 24-May-97, to lugnet.robotics.handyboard)
|
| |
| | clueless programmer
|
|
First time I have wrote to the list hope it goes well... To be honest I don't have a clue on how to program in 'C' or any thing else for that matter. But I'm slowly learning. I want to write a program similar to that of the Tutebot from the "Mobile (...) (27 years ago, 23-May-97, to lugnet.robotics.handyboard)
|
