 | | re: IR frequency (fwd)
|
|
Connect the ground from the oscilloscope to the HB ground (anyone). Connect the V from the oscilloscope to the + end of the LED driver (or the annode of the LED if it's connected). Adjust the oscilloscope until you get a visible square wave (...) (28 years ago, 30-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
Hello! I would like to know something: Does anyone know how the LCD screen on the Handyboard opreates? More specifically: 1) does it have 8 in ports (kinda like the opposite of a P.C.'s parallel port?) 2) does it have a strobe (or respond pin ) that (...) (28 years ago, 30-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Q1 : ztx614
|
|
hi, I have been working on the handy board for a couple of weeks now and I'm having problems finding the ZTX614 NPN darlington transistor, Digikey has them on back order until mid april. I was wondering if there is reason that it should be placed on (...) (28 years ago, 29-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | my HB project
|
|
Well, I just finished putting together my handyboard project. I thought maybe people would be interested in checking it out. It is a robotic camera moving thingy that is mounted on the front of my fish tank. It can move the camera horizontally so (...) (28 years ago, 29-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | re: IR frequency (fwd)
|
|
(...) signals at exactly 38KHz? somebody had suggested using an oscilloscope..but how do i go about it? (28 years ago, 29-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Sonar Transducer Multiplexor
|
|
(...) The OC is simply a protective buffer to the SPI pins. When the SPI feeds a low with a pullup resistor it must be able to sink the current drawn by the resistor. I read some of the docs on the SPI pinouts and ("M68HC11 Reference Manual" Serial (...) (28 years ago, 29-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Sonar Transducer Multiplexor
|
|
In your BMP circuit diagram that you posted recently, why did you use an open collector to feed the base of the transistor? Would it work if you connected the digital signal directly to the base? ---...--- ericson mar Master of Engineering Candidate (...) (28 years ago, 29-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR concept
|
|
(...) [Digitize the output from an IR LED with and without a signal present to achieve some common mode noise rejection.] This type of system is susceptible to being 'blinded' by high intensity IR sources (try it outside :-) I used a similar (...) (28 years ago, 29-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | u14
|
|
I had trouble finding u14(LM 2931Z-5.0). I thought I might be able to use the 78LO5A that was suggested as a replacement on the mini board. When I try to test the voltage on pin 28 of U2 as described in part 2 of the assembly manual I get 6.3 volts. (...) (28 years ago, 28-Mar-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR concept
|
|
In addition.... Perhaps I could use the on board IR header to turn on the 4 IR diode array with each diode in series with a current limit resistor and in parallel with the IR output header..?? (I think this has been suggested before.) (...) (28 years ago, 28-Mar-97, to lugnet.robotics.handyboard)
|
