 | | (no subject)
|
|
Please subscribe me to the handy board mailing list. Thank you very much. Michelle Conway ***...*** * Michelle Conway * wake up late and honey put on your * * Doyle 213 * clothes and take your credit card * * x3343 * to the licquor store, well (...) (28 years ago, 24-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
You are unsubscribed. For future reference, the way to unsubscribe is to write to me. fredm@media.mit.edu. -Fred In your message you said: (...) (28 years ago, 24-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | LM052L LCD Display
|
|
I have just had no success at all finding this part in the UK. I even talke to Hitachi UK and was told that if I wanted any it would have to be 100+ with a 20 week lead time! Now, I have an alternative fitted and working so there is no desperate (...) (28 years ago, 24-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | bipolar steppers
|
|
Suggestions Anyone???... Was wondering if anyone has an alternate solution to stepping a bipolar stepper? Currently.... I'm using an H-Bridge (driver if you will) SAA1042 (by Motorla) which is then getting its pulses from 1 of the motor outs on the (...) (28 years ago, 24-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | (no subject)
|
|
Can anyone tell me how to unsubscribe from the handyboard mailing list? thank you in advance, Zlatko Horvat (28 years ago, 24-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Problems with downloading
|
|
Tom: Your tests, specifically the fact that the HB's PWR LED comes on after download fails, demonstrate conclusively that the HB can *receive* data from your PC. This proves that the downloading software is able to open the serial port properly, and (...) (28 years ago, 23-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Problems with downloading
|
|
I'm trying to download the pcode_hb.s19 file to the handy board and I'm having a very hard time. I using win95 on a P5 and 200mhz. I setup the com port settings at 110 and no data flow. When I run the hbdl program and try to download the file I get (...) (28 years ago, 23-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | RE: dual servo update
|
|
(...) I use Futabas. The 32.768 mS interval is convenient because the 68HC11's 16-bit timer on a 2 MHz clock overflows at that time, allowing easier programming of the TOC functions. Has anyone found the upper limit on the time interval for Futaba (...) (28 years ago, 23-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IC loop
|
|
Hi Wade, You can use the "seconds()" function which reports elapsed time, plus a variable to keep track of when the loop should end: void main() { float end_time; end_time= seconds() + 20.; /* go for 20 seconds */ while (seconds() < end_time) { /* (...) (28 years ago, 23-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | IC loop
|
|
Hope someone can help, I have just written my first code for my bot. All I have done so far is make my bot go forward in about a 4 foot square area. I am now wanting to put a loop in the code so that it will continue for a certain length of time or (...) (28 years ago, 23-Jan-97, to lugnet.robotics.handyboard)
|
