 | | Handy board use in Micromouse
|
|
Hello, I am new to this group, so I may be repeating previously answered question. I wanted to know if anyone has looked into using the handyboard for building a Micromouse. Comments on their experiences and ideas would be appreciated. Tejesh (28 years ago, 22-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | LCD screen
|
|
After turning on my handy board after some traveling with it (and loading IC, etc) I have found that the contrast of the screen is very high. If looked at straight on the screen looks black (well, all black squares), but if looked at from an angle, (...) (28 years ago, 22-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | RE: dual servo update
|
|
(...) I send my servos commands every 32.768 mS, and they work fine. I don't know what the limit is, but I don't think that 20 mS (50 Hz) is critical. * Michael L. Ross/C33 | Lockheed Martin Eng & Sci Svcs Co. **** * Robotics Department | 2400 Nasa (...) (28 years ago, 22-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Sharp IS1U60
|
|
hi everyone, i bought 8 sharp IS1U60 IR detectors from Sterling Electronics.. (refernce "mobile robotics-inspiration to implementation) They have a $25 minimum purchase, the parts are reliable and are still working well for me. They cost $3.25 a (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | dual servos
|
|
Good Day, A consensus seems to be emerging among those who know more about pcode interrupt structure than I. The printf function does indeed disable the interrupts and run that way for quite a long time. Thus, the servo twitching seems to be mostly (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Twitchy servos
|
|
(...) I'm using a 80C32 board and control two servos by generating a PWM signal with a timer interrupt. It frequently happens that the servos twitch. In my experience the period of 50 ms of the PWM signal was too great. The problem disappeared when (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | MEMORY FAULT
|
|
When I turn my HB on I get the message "MEMORY FAULT" what does it mean and how do I fix it? Thanks, Peter Eacmen (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | RE: dual servo update
|
|
Two things to note in the servo investigation: (...) This supplies a reserve of current to the servos, and that allows them to seek to their desired position faster. (...) Two servos, when moving, can pull two AMPS of current. Thats 2000mA. Two (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Stepper Motors driving [DAT]
|
|
Hi - I am new to this list but the archive indicates some interest in driving stepper motors on the HB so here is my little bit: If we have a typical four coil, unipolar stepper such as those found in disk drives, they will have connections (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Demodulator
|
|
(...) I'll post this again: 4 sharp GP1U58Y: 40KHz IR Receivers for $12 From page (URL) them at mek-orders@orlandone...igital.net These are compatible with the IS1U60 as far as i know. I ordered 4 of them and they were shipped to me in the (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
