To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 7951 (+10)
  RE: 8450 Mission / Cybermaster expansion
 
(...) Not as challenging as getting one in Canada, I'll bet. I feel like a dope because my mother was just in Germany last month. Cheers, Ralph Hempel - P.Eng ---...--- A picture is worth a thousand words, but very few sets of a thousand words can (...) (27 years ago, 5-Nov-99, to lugnet.robotics)
 
  Re: 8450 Mission / Cybermaster expansion
 
Stefan Prescher skrev i meddelandet ... (...) Looking at the 8450 at www.lego.com I got the impression that there *was* a new programming system included, somewhat related to the RIS software. There's not much text, and just one little picture, so I (...) (27 years ago, 5-Nov-99, to lugnet.robotics)
 
  Re: 8450 Mission / Cybermaster expansion
 
Ralph Hempel skrev i meddelandet <000001bf27a7$d21b76...pro150>... (...) I think this will be very difficult/impossible, as the CM does not download the firmware - it's there all the time, in ROM, so you never download *machine code* to it, only (...) (27 years ago, 5-Nov-99, to lugnet.robotics)
 
  Re: What´s this new version of RIS?
 
(...) I think your question is covered by the following threads: (URL) Bak (27 years ago, 5-Nov-99, to lugnet.robotics)
 
  RIS 1.0 to 1.5 software upgrade
 
Recent purchasers of RIS 1.0 may order a software only update to 1.5 for a shipping charge only of $3.95, as indicated in the note from MINDSTORMS below. Consumer Affairs forwards you over to S@H to order, so have the rest of your holiday buy list (...) (27 years ago, 5-Nov-99, to lugnet.robotics.rcx, lugnet.robotics)
 
  RIS 1.5 upgrade kit arrived from S@H
 
The RIS 1.5 upgrade kit I ordered from S@H arrived yesterday. Among that handful of new pieces, I like the trans-blue connector pieces the best. This connector piece provides an easy yet durable way to change the XYZ orientation (i.e., which side (...) (27 years ago, 5-Nov-99, to lugnet.robotics)
 
  Re: How to communicate sensor value changes to RCX Tower
 
I believe that Variable 0 can be used as a flag and there is a special way to constantly poll for a change in that value. Perhaps you could have a task that logs all sensor values into the RCX DataLog and use Variable 0 to indicate when the DataLog (...) (27 years ago, 5-Nov-99, to lugnet.robotics)
 
  Re: How to communicate sensor value changes to RCX Tower
 
Farrukh S. Najmi <lego-robotics@crynwr.com> wrote in message news:3822F0C7.A06551...sun.com... (...) I doubt you can beat just polling it to death. Anything else might be a little more efficient, but will probably introduce delay and complexity. (...) (27 years ago, 6-Nov-99, to lugnet.robotics)
 
  Re: Uploading NQC programs to legomindstorms.com personal pages
 
John VanZwieten <john_vanzwieten@email.msn.com> wrote in message news:FKqG9J.J4J@lugnet.com... (...) of (...) At Mindfest Russ and many other LEGO folks showed a genuine interest for what goes on in this list. I'm glad to see they have turned off (...) (27 years ago, 6-Nov-99, to lugnet.robotics)
 
  Other missing groups? (was: Re: Fabuland group (was: Re: 34 new newsgroups!))
 
(...) No, it wasn't left out on purpose -- it was just an unfortunate oversight. In fact, Fabuland was listed on this page long ago, (URL) a niche thematic-interest group likely to pop up...it's always been something inevitable. So -- Are there any (...) (27 years ago, 6-Nov-99, to lugnet.admin.general, lugnet.general, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR