To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6941 (+10)
  Re: Light sensor values
 
Richard <richard@mailstart.com> wrote in message news:FI88pu.4Js@lugnet.com... (...) when (...) cells? CdS sensors are pretty slow, but I don't think the ones I'm using take 5 seconds. I have used the Radio Shack 276-1657 and the Mouser 338-54C348 (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Motor Control
 
Hi everyone. I'm new to this site and was wondering if anyone has the information I need. 1)Who makes the UCN 5804 Uni-polar stepper driver and is it still made? 2)Where is a good place to find a wide selection of hobby size stepper motors on a (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: color sensor: was ( Light sensor values)
 
Pure-Lego (but more than one input/output unless a motor can be driven off of the output to a light sensor and the input from a light sensor and rotation sensor can be multiplexed): 1) 1 light sensor 2) 1 (micro)motor to drive the rotation of the (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: color sensor: was ( Light sensor values)
 
More simlple : use the sensor input mux by Michael Gasperi. You can easily connect 3 (up to 7) passive sensors to one RCX input. I've completed mine, but didn't test it already. "Stephen P. Gibbons" a écrit : (...) ---...--- Philippe Jadin (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: Motor Control
 
(...) There is probably no ready-to use chip to control a servo with a digital value. But you have two solutions : 1. Try to program a pulse width modulated signal output. You need a fast "brain"... 2. With an digital to analog converter and a 555 (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: Dual Differential Adder/Subtractor (again!)
 
christie <lego-robotics@crynwr.com> wrote in message news:199909151742.KA...ple.com... (...) "adjacent" (...) link on (...) You are quite welcome. Sorry about the lack of an EMAIL address, my son Michael setup the page and he has not done this (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  IRPD revisited
 
Hi All, Dennis Clark gave us a great design for a two channel infra-red proximity detector. It works well in a large number robot designs. I have just completed an IRPD with a slightly different design point. It is a single channel detector, housed (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: IRPD revisited
 
(...) Very nice! Although I think your statement about robots breaking apart when they hit a wall is a bit over-dramatic. Lego creations stick together pretty well -- I've built a large number of robots with mechanical bump sensors. That's not to (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: color sensor: was ( Light sensor values)
 
Stephen P. Gibbons <lego-robotics@crynwr.com> wrote in message news:37E361B0.6CA5FE...ech.net... (...) of the (...) sensor can (...) given (...) You have a good idea, but the LEGO light sensor is a silicon photo transistor which is mostly sensitive (...) (27 years ago, 18-Sep-99, to lugnet.robotics)
 
  Re: IRPD revisited
 
Matthew, I agree. Depends on the speed of the robot. If the bot is moving slow enough, touch sensors are fine. There are probably configurations with long mechanical "feelers" that will work well at higher speeds. From what I have seen, adults seem (...) (27 years ago, 19-Sep-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR