 | | Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0]
|
|
(...) I don't doubt that there are reasonable creations that e.g. press a touch sensor button halfway for extended periods of time, but I can't think of any off the top of my head. Can anybody help me out here? My point was that in what I would (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: multiplexed touch sensors [was: Re ideas for a RIS 2.0] [DAT]
|
|
(...) Okay, I felt like I had some time, so I looked into this a bit. I skipped the first part and jumped right into measuring a waveform. I measured a faster waveforms for now, but might give it another go with a longer waveforms and higher (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | RE: Touch Sensor as a Switch
|
|
In response to my own post on the Cybermaster touch sensors: The three different Cybermaster touch sensors have a resistance of 15k, 12k, and 10k when not pressed. The rest of my ramblings were pure fiction. The three Cybermaster inputs are (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: robotic rovers
|
|
(...) Have you tried combining the inputs of the two output motors into a differential? If the inputs are counter-rotating, the net differential body rotation will tell you which side is moving faster, ie: Motor A ------> Differential <--(Reversed (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Use a RCX as a Sensor port AND a Motor Output!
|
|
So, I was messing around w/ the RCX and hooked up a Micromotor to one of my output ports and lo and behold....I could control the motor by toggling the Sensor Type for that port between a Passive (None, Switch, Temp) mode = OFF and an Active Mode (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Use a RCX as a Sensor port AND a Motor Output!
|
|
Ooops, subject should have been: Use RCX Sensor Port as a Sensor Port AND a Motor Output! Dave (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Robot related books...?
|
|
(...) Having cracked mine, I'd have to say "great book". Lots of helpful stuff for the home hobbyist in that one. jack j-perdue@tamu.edu (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Use a RCX as a Sensor port AND a Motor Output!
|
|
Great work! Extra motor output, speed sensing, stall detection and sensor/motor multiplexing. Thanks for the research! (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Climbing robot?
|
|
Where can I find more info on the Fudd stair climber? I couldn't find anything in the LUGNET newsgroups. (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Search Sub
|
|
I just received my search sub today. It was a great deal from shop@home. Half price, just $25. In addition to standard extra parts, it contains an air tank, a large pump and a large piston. Joel Shafer joel@connect.net -- Did you check the web site (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | RIS 1.5 defined???
|
|
Forgive me if this is old news, but.... It looks as if RIS 1.5 is just a software/constructopedia update, and that the RCX used is still the 1.0 version... check out: (URL) you check the web site first?: (URL) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | RE: Touch Sensor as a Switch
|
|
(...) My guess would be that it lets you determine which colour switch is attached to each input, when it is in the open state. Kind of a nice idea actually - just attach a switch to any port, and the GUI can remind you which colour sensor is (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Touch Sensor as a Switch
|
|
Tilman Sporkert skrev i meddelandet ... (...) It's for the CM software - it's targeted for younger kids than the RIS. As the sensors have different color (and open resistance), the software assumes you build the models as described, and then just (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: Q:Best approach to line tracking
|
|
I've used a similar approach, and it does work, but you still can't go very fast. I'd like to try a double sensor approach, myself ... have a friend bringing a second set by this weekened. (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | ***Multiple Switches***
|
|
Hi all, Mt question is has anyone been able to use multiple switches on the same port while each switch would be read as a different value? Would a resistor in line work? And How would I address it, Maybe as a light sensor? Any help would be very (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Programming DDK Micro Scout Info
|
|
Hi all, I just got off of the phone with folks at Mindstorms Tech Support. I asked if the RCX 1.0 could program the Micro Scout in its "P" mode - The answer was "No, we think that the Scout will be set up to do that, but not the RCX." Bummer. (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Droid Developer Kit, Robotics Discovery Set
|
|
We'll have the Droid Developer Kits ($99.99) and Robotics Discovery Sets ($149.99) in stock any day now... The Lego Company has shipped our first pallets. Jason Cooper - robotman@slip.net Mondo-tronics' Robot Store (URL) you check the web site (...) (27 years ago, 26-Aug-99, to lugnet.robotics)
|
| |
 | | Re: robotic rovers
|
|
(...) Yeah... the LDrawn design I came up with is at (URL) I'm very happy with because with two differentials it allows me to track both linear and rotational motion. (27 years ago, 27-Aug-99, to lugnet.robotics)
|
| |
 | | Re: robotic rovers
|
|
(...) Perhaps you could compromise - mount the RCX facing forward for proximity detection and point the IR transmitter downward - say, suspend it from a ceiling fan ;). I'm still going nuts over that ping routine you came up with - a stroke of (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
|
| |
 | | Re: ***Multiple Switches***
|
|
I believe a someone has tried this method using a resistor block. More info can be found at (URL) wrote in message <771d7d14.24f70aa5@aol.com>... (...) (27 years ago, 27-Aug-99, to lugnet.robotics)
|