To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6471 (+10)
  RE: r/c servos and firmware
 
Ok, Here's my 2 cents on servos...read to the bottom if you are interested in helping to develop the code for this. The servo takes a 60Hz (approx) pulse width signal between 1 and 2 msec The pulses are fed into a little circuit that generates an (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) OhOh, I've piqued my own interest. I've looked at the H8 hardware manual and the RCX internals. The OC1A triggers every msec, except the stupid routine clears the Free Running Timer every time!!!! So much for using the OC1B, maybe. The minimal (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Okay! Finally I got it! (-: It sounds to me like servos can't rotate continuously in the same direction. In other words, they're good for steering but not for turning the wheels that make the car go. Is that right? Anyway, having heard that (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) There are multiturn servos for winches in RC sailboats, but they are REALLY expensive. (...) Well don't give up too fast. They ARE useful for steering, or lifting, or grabbing because we can set the limits of motion. This makes things like (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Using RCX with Lego Trains
 
I just picked up the Lego "Railway Express" set (#4561) last night. It comes with a "Toy Transformer" electrical plug (adaptor). The label on the plug says (North American version): Input: 120 VAC 60 Hz 0.12 A Output: 12 VAC 7 VA Would this work as (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Almost exactly how I'd do it. The problem is what if OCIB must be set to a small value, and the FRT has already passed this value when the OCIA handler sets up OCIB in step 3? This problem is solvable. If the total interval is closer to 1 ms, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) Let's say a 0.7 ms pulse results in a rotation of 0 degrees. Let's say a 2.0 ms pulse results in a rotation of 180 degrees. If all you had were 0.7 ms pulses and 2.0 ms pulses, you'd be able to choose either 0 degrees or 180 degrees, resulting (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Exactly. See (URL) examples. These servos have a little disc or cross on top with holes at the edges. The servos can turn the disc only 45 degrees in each direction. They are used for moving flaps or rudders on model airplanes. You bend a 90 (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Whew! I'm glad I got that much right :-) (...) We could check OC1B and if it's "close" just turn off the motor...as far as the long timer goes, OC1A should always force the output off...on the other hand, the OC1B could be set NO GREATER than (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) In (...) make (...) least (...) Hello, New mindstorm user...been lurking for a while. WRT to servo motion -- it is fairly easy to modify standard servos for continuous motion. $ would put this motor about the same cost as lego so not sure of (...) (27 years ago, 21-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR