 | | Re: Best (disposable) battery for the RCX?
|
|
It's strange that you say alkaline batteries don't "seem to last very long at all". I've been using mine for over a month. You should probably qualify your statement by saying how many minutes or hours you've run the motors on those batteries. (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) All you need is to put a differential between the wheels. If those wheels need to have traction, all you have to do is to apply the force to the differential itself and the differential will distribute the traction for the two wheels like a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Best (disposable) battery for the RCX?
|
|
Well, I wouldn't really even use the batterires unless I was going to do some robot that had to be moving around. I would just use an AC Adapter for it. Simplistic and cost effective instead of blowing 6 batteries in a few short hours of using the (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Mechanical question
|
|
I've been puzzling over this one, and I still don't really understand it: Why can a bot with tank treads do a turn in place, while a bot with four wheels geared together so that the front and back wheels on each side always move together can not? My (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Best (disposable) battery for the RCX?
|
|
In lugnet.robotics, Jon Shemitz writes: [snip] (...) I use Rayovac Renewal rechargable alcalines myself. I get lots of time on each charge and can use the same cells over and over again for over a year. I get a four pack of AAs for about $6 and (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) Maybe I did not phrase my problem clearly. It's better described in Jon Shemitz's recent post (URL). In my experience, wheels are more efficient than treads. Under the same load, my wheel-based design outrun my tread-based design. However, (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) [snip] (...) You are close here. Tank steering is often called "skid" steering because tank tracks are optimized for traction parallel to direction travelled and have little traction in a tangent direction. A look at the tread pattern will (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
This isn't an answer, but why not just make a three wheeled bot. You can place the third pivot wheel inside the radius of the two outer wheels, and you'll have a bot that turns in place. Most of my bots are of this design. Here is a crude ASCII (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
I haven't tried it myself, but I've heard that you can make your RCX program respond to three of the buttons on the RCX remote control. You can also (if you need more than three commands) use a second RCX as a remote control. I've run across a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) Have you seen the mars rover turn? If you have the parts for it, you could add a steering mechanism in the front wheels and another for the wheels in the back. Humm... that should make an interesting mechanical project :-) Laurentino Martins [ (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|