To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 481 (+10)
  Re: Main ROM routine
 
(...) Memory-mapped motor drivers, yes. A strange way to do things. But f000 is only written and never read, so it must be that way. -Kekoa (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: some interesting lego building
 
This kind of info is on LEGO ON MY MIND too: (URL) Triangles in menu There you'll see some explanatory pictures/animations as well. Eric Brok Greg Alt wrote in message <199811112132.NAA272...mo.com>... (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Main ROM routine
 
(...) This bit was me, for the record: (...) Not that strange - when I worked on embedded systems, we often did this. When you get down to it, from the electronics point of view, the difference between I/O and memory is typically just 1 signal line (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Multiplexing Input Circuit
 
I think Sven thought of this first. Anyway I threw a circuit together last night that uses the SetSensorType to switch between 4 inputs. I put it on a page at: (URL) seems to work well, but startup is a problem. It starts out on input 1 but if you (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) Require it to be clocked every so often, reset if it is held high for a certain length of time. Alternatively, it may be possible to drop the voltage to zero - but that would require a firware change... anyway, I'll look into it out of (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) Looks good! How about using the third input port to assert the reset line and set the counter back to zero? Is your counter set up as a binary counter? From your diagram it looks like there are times that more than one sensor would be active (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) The counter is a CMOS decade counter that has only one output high for each count. There is only one analog switch on at a time. The counter is reset when it hits the value 5 so it jumps back to 0 to start over. The analog switch is (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Tachocount
 
(...) I'm sure the motors may be used for other things as well, albeit not as easily as separate motors. (...) But in a program you will always know which way the motors drive, right? So one can possibly maintain a second variable for each motor (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) The setup I was using was bi-directional too, I'm not sure exactly why I was seeing it, but I remember getting a high reading for a non-pressed touch sensor when the next one over (the previous one in the cycle?) was pressed. If I reversed the (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: A spider (legged) RCX robot
 
(...) for moving the legs up and down very thoroughly, but not the rotating of the legs. The first time I saw the article, I thought the model moved by always keeping at least four legs fully extended. I later learned that this was not true, but I (...) (28 years ago, 12-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR