 | | Re: Steer kit
|
|
David Cuthill <lego-robotics@crynwr.com> wrote in message news:01BE8DCB.0A59FE...ome.com... (...) One of the models on this page shows some of those parts. Sorry that they are not closeup. (URL) (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Steer kit
|
|
I bought the Steering kit, 5295, and now can't envision how all of the pieces can be used. Does anyone have any examples they could share? -- Did you check the web site first?: (URL) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Reading sensors at equal intervals.
|
|
Is it possible (with the standard firmware) to read the RCX sensors (actually, ideally, to run any old subroutine) at equal intervals, ie like every 100ms or something? (I assume it must be, otherwise you couldn't measure speed with the angle (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Pics of 1999 Mindstorms items
|
|
The press room at www.legomindstorms.com has some new pictures of the two new kits due out this year. From these pictures, it's clear that the "Scout" unit - in the Robotics Discovery Kit - is very similar to the RCX; it has only 2 inputs, and (...) (28 years ago, 24-Apr-99, to lugnet.robotics)
|
| |
 | | Re: pneumatic switch control
|
|
At 05:13 AM 4/23/99 -0400, you wrote: <snip> (...) Awesome. It was easy to think of, but I'm not sure that I could have built it as well as you. I particularly like the cam mechanism that you developed, and the use of just one touch sensor. Very (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Using Lego IR outside of Lego
|
|
(...) If your laptop has one of the newer (1997) or later super-io chips as the controller for the IR, you may be able to get it to communicate with the tower. The trick is to setup the chip into SHARP IR mode (which transmits data at 38.4k on a (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | Re: SoCal LegoLand
|
|
In article <199904222202.SAA232...navy.mil>, Ken Hornstein <kenh@cmf.nrl.navy.mil> writes (...) and in article <371FBB6F.236FDCF8@ghg.net>, John A. Donaldson <jdonaldson@ghg.net> writes (...) I'm 56 and drove _past_ Billund last September without (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | Re: pneumatic switch control
|
|
I just got my RIS as well as some pneumatic parts yesterday. The timing couldn't be worse as I'm in the middle of finals and can't spare much time for non-studying activities. However, your suggestion inspired me to take a study break and open up my (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | Re: pneumatic switch control
|
|
(...) To connect the motor to the switch, use a piston arrangement (like a car engine). This can be done quite compactly. A single touch/light sensor and medium pulley wheel can be used to count motor revolutions (to determine when you've gone from (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|
| |
 | | virtual RCX-unit
|
|
Hello everybody! The most of RCX owners have only one RXC unit. So the created RXC-robot seems to be lonely and often does not communicate with the PC after downloading a program.. Have anyone ever think of programming a (or many) virtual RCX (...) (28 years ago, 23-Apr-99, to lugnet.robotics)
|