 | | Re: rcx acronym?
|
|
Chris Stanley wrote in message <36A24985.7755166A@usit.net>... (...) I asked this to the Mindstorms helpdesk once. In an e-mail thay said: Robotic Control X (Or Robot Control X - from memory). So the X is just for decoration. Eric (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Working around the 3 output limitation
|
|
snip (...) Actually there is a working LEGO compass, put probably not large and reliable enough to be read by a sensor. Eric Brok (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | RCX program editor review (second version)
|
|
I know that I should not comment on what you write about my own program (RcxCC) but I feel that I should because you are looking at version 1.0 while 2.0 is already out for a while and is so much more extended. It does have online help, visual (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Fw: Fw: Alternative Mindstorm Robotwars
|
|
-----Original Message----- From: Tom Rowton <trowton@broadcast.com> To: champs <champs@obscurity.com> Date: Monday, January 18, 1999 7:58 AM Subject: Fw: Fw: Alternative Mindstorm Robotwars 3-D(imensional)3-A(xis) Maze - OR - 6 degrees of freedom (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: legOS problems
|
|
Hi Brian, I have a problem compiling legOS under Windows95. Whenever I type 'make' it ends in error saying: make: *** No rule to make target `include/sys/mm.h' needed by 'kmain.o'. Stop WHat am I doing wrong? thank you in advance Tadija -- Did you (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Fw: Alternative Mindstorm Robotwars
|
|
(...) Good idea! Just make sure you don't let in any of the ping-pong retreival bots in, especially those that throw the balls..... (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Fw: Fw: Alternative Mindstorm Robotwars
|
|
It would be a non-trivial task for a lego bot to throw one of those...the one's I've seen are about 5" in diameter and made a fairly heavy duty plastic...add to that the (small) weight of a hamster or gerbil, and I don't think it would be _near_ as (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX program editor review (second version)
|
|
Mark, (...) If you are referring to the review which is also on the Lego-Robotics wiki site at: (URL) I would think it would be acceptable for to add your own comments to that page. Since the review is originally by Denis Cousineau then I think you (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Super Car 8880
|
|
(...) This gearbox is also used in other kits like the technics Space Shuttle (1300+ technic parts). The gearbox lets you use one motor to gain four different outputs. Looking at the picture you see four dark grey gear wheels. These are not fixed to (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | New hydraulics
|
|
In the 99 catalog ther is mention og a new hydraulics system that has very smooth motion according to the sales-pitch. The sets are not availible in Norway yet, so I wondered: Have anyone seen this new hydraulics, and is it any good? Will it be (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Light outputs on RCX
|
|
Has anyone ran lights from the RCX outputs? I need something brighter than an LED, any ideas? Thanks, Bryan Bible --- __o --- __o Tandem Computers --- _ \<,_ --- _ \<,_ Austin Texas --- (*) / (*) --- (*) / (*) bryan.bible@compaq.com -- Did you check (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I took apart a laser pointer. I put the laser module into a mutilated brick. I added a diode, an LM-317, appropriate resistors and a .1uF capacitor to make a 3 volt power supply. The diode makes it so the laser is on for motor forward, off for (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
Paul Haas writes: > On Mon, 18 Jan 1999, Bible, Bryan wrote: > > > Has anyone ran lights from the RCX outputs? I need something brighter than > > an LED, any ideas? > > I took apart a laser pointer. I put the laser module into a mutilated > brick. I (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Where is "R4" on Handy Board Extension Schematic?
|
|
I have just finished building the extension board, and, while it appears to work all right, I can't seem to find resistor R4 on the schematic. The power transistor near the on/off switch is getting quite hot with the expansion board piggybacked on (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: new Throwbots
|
|
(...) I doubt that these joints will be of much use - they're way to rigid, and there is not a real good place to attach a motive link. (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Light outputs on RCX
|
|
(...) I made several diffrent color (even flashing!) lights with the mini xmas lights. they are real bright if you set the output to 8 or they work at any level. I took the bulb out of the little plastic holder and soldered wires to the wires on the (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: new Throwbots
|
|
(...) I just bought 2 of the new throwbots, Granite and Electro. I am not very impressed. The best part about them is the colored gears. Only because I am tired of gray. ---...--- @¿@ (URL) ,-, Follow the adventures of Capt. Jack Napalm! One thing (...) (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) As a first step, how about simple 2 *4 s with logic gates in them? one of the connectors below for power, one output below, and two inputs on top :) Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) Whereas I have lost it several times form turning the RCX off.. a real pain. Jasper (28 years ago, 18-Jan-99, to lugnet.robotics)
|
| |
 | | RE: RCX 2.0 -- ideas.
|
|
(...) Actually I'd be happy with just some Lego resistors, a 2X1 plate with the two studs as contacts and a resistor between them :) 100% pure multiplexed touch sensors Oh well. -- Did you check the web site first?: (URL) (28 years ago, 18-Jan-99, to lugnet.robotics)
|