To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23849 (-20)
  Re: GPS Reality?
 
Its worth pointing out that there has been recent discussions on the DPRG list about small scale location - a discussion which started off on GPS. I think it has now progressed to a system combining three sonar beacons, which are broadcast a radio (...) (22 years ago, 10-Apr-05, to lugnet.robotics)
 
  Re: Gearbox
 
(...) Since you're using a pendulum, why not use an escapement like a clock? The pendulum permits the release in one direction of a certain amount of rotation of the escapement wheel, which is spring or elastic-band powered. An important thing to (...) (22 years ago, 9-Apr-05, to lugnet.robotics)
 
  Re: RCX and R/C combined
 
(...) Hi Steve, I built this little resistor bridge out of 10K resistors for a similar application: (URL) Note: You can't see it in the photo, but the 1x4 electrical plates on the underside of the 2x4 plate have been cut in half so you can attach a (...) (22 years ago, 9-Apr-05, to lugnet.robotics, FTX)
 
  Re: GPS Reality?
 
(...) It's probably possible - making an infra-red transmitter to sit on the GPS side would get you there if the GPS could be made to run at a low enough baud rate. Alternatively, you could modify the RCX to take in RS-232 directly...but that's (...) (22 years ago, 9-Apr-05, to lugnet.robotics)
 
  Re: GBC 6 - the obsession continues...
 
Hi Danny, (...) that shouldn't be impossible, but just adding a motor was easier. Jürgen (22 years ago, 9-Apr-05, to lugnet.robotics)
 
  Re: RCX and R/C combined
 
(...) snip (...) I'm only intending to use standard gear motors. Great answear Mark, that's exactly what I wanted to know. Steve (22 years ago, 9-Apr-05, to lugnet.robotics)
 
  Re: My First MOC
 
(...) Rather than asking everyone to email you replies, you may want to look into subscribing to the group (perhaps temporarily) by email, via this URL: (URL) first doing this subscription setup: (URL) to get your confirmation code ) XFUT (...) (22 years ago, 9-Apr-05, to lugnet.robotics, lugnet.technic, lugnet.admin.general)
 
  My First MOC
 
Pictures should be forthcoming in a few days of my first official MOC, the überCrawler. This is a 2 RCX, 6 motor beast that turns by raising itself via a two-motor winch. It has four independently-powered tracks, coupled into a front and rear pair (...) (22 years ago, 9-Apr-05, to lugnet.robotics, lugnet.technic)
 
  Gearbox
 
Does anybody have diagrams, pictures, etc., regarding a "one-way" gearbox? This would have ideally one input and one output shaft, and the output shaft would turn the same direction no matter which direction the input was turned. Like a rectifier (...) (22 years ago, 9-Apr-05, to lugnet.robotics)
 
  GPS Reality?
 
Is the idea of a GPS sensor compatible to the sensor ports an absurd idea? I have a few old Garmin units, with RS232 ports on them. I know of people who have incorporated these units successfully into "real" robots, but that usually involves heavy (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
 
  Re: RCX and R/C combined
 
(...) Here's a diagram of the RCX sensor port circuit: (URL) Feeding a voltage of up to +9V (or the RCX battery voltage) will not harm the port, as this is what it uses in Active mode (light or rotation sensor). You can actually use an external 9V (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
 
  RCX and R/C combined
 
I've just been experimenting with my RCX to see if it can sense the output from the Lego RC unit. The experiment was fairly successful, I was just wondering though if putting 9v into a sensor port does it any good. Are their any risks in making such (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
 
  Re: Looking for the Mindstorms software.
 
(...) No it is not incorrect. You do have to install the USB tower drivers in order for NQC and BricxCC to use the USB tower to talk to the brick. That is not the case for the Serial tower. You can get the tower drivers (along with the firmware) by (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
 
  Re: caster wheel design
 
here's some raw pix of one completed robot, another in construction, and an idea for a third, all using the omniwheels: www.danbmil.com/lego I'll try to clean up the pix, put some captions etc. later - dbm ps note that the additional duplo blocks (...) (22 years ago, 8-Apr-05, to lugnet.robotics)
 
  Re: caster wheel design
 
(...) Hi Dan, Maybe, could you provide some pixs of the heavy robot you built using the omni wheels. Thanks, Hakim (22 years ago, 7-Apr-05, to lugnet.robotics)
 
  Re: caster wheel design
 
Wow, where did you find it? I will get four of these to me... Thanks "dan miller" <lego-robotics@crynwr.com> escreveu na mensagem news:20050407113954....hoo.com... (...) robots quite easily. You (...) tricky because the (...) lateral coasters is (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
 
  Re: caster wheel design
 
you can use omniwheels, like the ones from Charmed Labs: (URL) only sell the single-row ones, but the double-row ones ((URL) can be adapted to Lego robots quite easily. You can also combine two single-row ones to work like a double, but it's a bit (...) (22 years ago, 7-Apr-05, to lugnet.robotics)
 
  unsubsribe
 
lego-robotics unsubscribe (22 years ago, 7-Apr-05, to lugnet.robotics)
 
  Re: GBC module screw
 
(...) Ah, you have beaten me on the Archimede screw... I was thinking of this one, but I didn't get the screw right yet. Congratulations! Nice usage of micromotor. But it is slow, what is the ball throughput of your module? Any chance to look at a (...) (22 years ago, 7-Apr-05, to lugnet.technic, lugnet.robotics)
 
  Re: Land Walker
 
(...) Yes, it is. I would love to slide on down the street in that! (...) Kevin (22 years ago, 7-Apr-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR